Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 232

Page: 232 / 366

7.6 Station Message Detail Recording

Table 39: Station Message Detail Recording Troubleshooting

Symptom

Probable Cause

Corrective Action

IP trunk call unsupervised

transfer and queued to

ACD path reports path

extension instead of path

reporting number.

Refer to Mitel

Knowledge Base article

06-9999-00002 for possible

causes.

Refer to Mitel

Knowledge Base article

06-9999-00002.

When making a call in

or out on SIP trunks the

trunk number in the SMDR

record is blank.

SMDR for SIP Trunks

use the SMDR Tag field

from the SIP Peer Profile

form for the trunk number.

If this field is blank, the

trunk number in the SMDR

record is blank.

Enter a Trunk Number

(for example, 99) in this

field and the number will

be displayed as the trunk

number in the SMDR

record (for example, T099).

Entering a non-verified

account code during a

call generates a single

SMDR record instead of

the normal two, one for the

initial call and a second for

the subsequent account

code entry.

Account code entered

within five seconds of call

answer.

Change the “Suppress

Initial SMDR record with

Account Code Entered

Time” in the SMDR Options

form in ESM. The default

is five seconds which

generates one SMDR

record if the account code

is entered within 5 seconds

of answering a call. If the

account is entered after 5

seconds, two records are

generated.

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands