Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 214

Page: 214 / 366

Tools and Embedded Applications

7.3 Emergency Call E911 Support

Table 36: Emergency Call Support Troubleshooting

Symptom

Probable Cause

Corrective Action

Emergency calls do

not trigger E911 local

notification. Calls

placed on a designated

“emergency” route do not

trigger local notification.

E911 local notification

will not be activated

if an

emergency hunt group

is not fully programmed

and a call is placed on a

designated “emergency”

route

Refer to Mitel Knowledge Base

article 04-1000-00020 for

programming instructions.

Emergency call does

not trigger E911 local

notification

Enhanced 911 (E911)

operation not fully

supported for the

device. There are some

exception cases whereby

emergency calls do

not trigger E911 local

notification.

None. Currently, the following

devices do not fully support

Enhanced 911 (E911)

operation:

•

Hot Desk users

•

IP consoles

•

Teleworker Solution users

•

Your Assistant and Your

Assistant Softphone users

•

Any other mobile IP phones

or phones that are carried

from location to location

Refer to the Engineering

Guidelines for details.

•

Troubleshooting MiVB Next Generation 911 (NG911) with Red Sky

on page 208

7.3.1 Troubleshooting MiVB Next Generation 911 (NG911)

with Red Sky

This section outlines the possible issues with MiVB Next Generation 911 services and

the steps to troubleshoot NG911 issues with Red Sky.

Types of issues that can occur:

Document Version 1.0
Troubleshooting Guide

208

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands