manualshive.com logo in svg

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

The Mitel MiVoice Business 3300 ICP Troubleshooting Manual is an essential resource for users of this versatile business communication system. Download this comprehensive manual for free from our website and discover in-depth troubleshooting advice to maximize the performance and efficiency of your telecommunications infrastructure.

Share
Download
background image

Trunking

6.4 XNET

Table 30: XNET Troubleshooting

Symptom

Probable Cause

Corrective Action

Caller reports

reorder tone when

calling to another

system.

Errors in the XNET ARS

programming.

•

Ensure that the ARS Leading

Digit Assignment and ARS

Digits Dialed Assignment forms

translate the dialed digits to an

XNET route. Either the digits

do not resolve to a route, or

the route does not have the

XNET Trunk Group Number field

programmed.

•

Ensure that the PBX Number

field in the IP/XNET Trunk

Groups form contains a system

number which exists in the XNET

network.

•

Ensure that the PBX Number

field in the IP/XNET Trunk

Groups form contains a

PBX number that is correctly

programmed on the Remote

PBX:

•

The incoming signaling DID

number at the Remote PBX

may not match the correct

local outgoing list.

•

The incoming voice DID

number at the Remote PBX

may not match the correct

local outgoing list.

•

Interconnect restrictions may

be set up incorrectly in the IP/

XNET Trunk Profiles form at

the Remote PBX (the remote

profile number may not agree

with the correct local profile

number, or may be the wrong

setting for the profile).

Document Version 1.0

185

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVoice Business 3300 ICP

Audipack VCL-1UP Installation Manual preview
VCL-1UP
Brand: Audipack Pages: 12
Ascon tecnologic vP4 Installation Manual preview
vP4
Brand: Ascon tecnologic Pages: 4
Cobolt TC1290MS Instruction Manual preview
TC1290MS
Brand: Cobolt Pages: 5
Nikkei NMD315 User Manual preview
NMD315
Brand: Nikkei Pages: 28
PACH & COMPANY AeGIS 8000 Series Quick Installation Manual preview
AeGIS 8000 Series
Brand: PACH & COMPANY Pages: 14
Avaya Tandberg 150 MXP Installation Instructions Manual preview
Tandberg 150 MXP
Brand: Avaya Pages: 13
AbleNet TalkingBrix 2 Quick Start Manual preview
TalkingBrix 2
Brand: AbleNet Pages: 8
TechniSat Car Radio Operating Instructions Manual preview
Car Radio
Brand: TechniSat Pages: 24
Zenitel Phontech ICS 6200 Installation Manual preview
Phontech ICS 6200
Brand: Zenitel Pages: 193
Okuma VTM-200 Operation & Maintenance Manual preview
VTM-200
Brand: Okuma Pages: 109
Philips FW545C Specifications preview
FW545C
Brand: Philips Pages: 2
Philips FW540C Specifications preview
FW540C
Brand: Philips Pages: 2
Philips FW390C Specifications preview
FW390C
Brand: Philips Pages: 2
Philips FW56 User Manual preview
FW56
Brand: Philips Pages: 24
Philips FW545 Manual preview
FW545
Brand: Philips Pages: 26
Philips FW585C User Manual preview
FW585C
Brand: Philips Pages: 27
Philips FW380I User Manual preview
FW380I
Brand: Philips Pages: 28
Philips FW540C Owner'S Manual preview
FW540C
Brand: Philips Pages: 86

Brands by name

Popular brands

Load more brands