manualshive.com logo in svg

Mitel DBC 223, Directions For Use Manual, Page: 57 / 121

Share
Download
Mitel DBC 223 Directions For Use Manual Download Page 57

M

I

V

OICE

 4223 O

FFICE

 (DBC 223) 

FOR

 M

I

V

OICE

 MX-ONE

57

3/1553-ANF 901 54 Uen F5 2018-12-03

provide this functionality ( 5.2 Conference on page 55 and 5.7 Transfer on page 

57 ).

•

Dial the extension/external number.

To revert to original party

•

Press the Clear-key (if you have finished the inquiry).

•

Press the Line-key that is parked.

Other features available during inquiry are:
•

Refer back ( 5.10 Refer back on page 59 ).

•

Transfer ( 5.7 Transfer on page 57 ).

•

Conference ( 5.2 Conference on page 55 ).

5.5 

INTRUSION

Depending on the authorization of your extension there is another option for getting 

through to a busy extension. You can use Intrusion which means that you are 

connected to ongoing call after a short tone burst.

To order intrusion when meeting busy

•

Press the soft-key 

Intrusion

  or the Intrusion-key or dial 4.

If intrusion on the called extension is not allowed, you will continue to receive busy tone.
Before the intrusion is performed a warning tone is sent to the parties in the ongoing 

call. During the time the three parties are connected a warning tone will be heard.

Note:  

The warning tone, both before and during the intrusion, can by categorization 

be disabled

5.6 

INTRUSION ON A SPECIFIC EXTERNAL LINE

If the external line is busy you can intrude. You can use Intrusion, which means that 

you are connected to ongoing call after a short tone burst.

5.6.1 

TO INTRUDE

•

Dial *44*individual external line number# and external destination code (busy 

tone).

•

Press the soft-key 

Intrusion

  or Intrusion-key or dial 4.

5.7 

TRANSFER

You can transfer a call to another extension (in your exchange or private network), 

subscriber or the PBX operator. If you have more than one parked call it will be the last 

parked call that will be transferred.

Summary of Contents for DBC 223


























































































































Reviews:

No comments