background image

Contact Miseno at (855) 480-2915 or email [email protected] with any questions. Copyright ©2019, Miseno. All rights reserved

PAGE 2

Skirted HET Single- and Dual-Flush Toilet

Installation Instructions

Step 2. Install toilet base.

E.

 Place toilet base upside down on a clean surface.

F.

 Install a bead of sealant or plumber’s putty around the foot of 

the base (see illustration).

G. 

Lift the base, flip it over and lower it into place on the floor 

outlet flange. Align the connection “L” brackets to the connec-
tion holes in toilet base. Bracket ears should poke through 
slots in toilet base.

H. 

Firmly push toilet down to seat the outlet horn into the 

rubber gasket on the seal plate assembly. Set toilet by firmly 
pushing down at all points around the perimeter of the base.

I. 

With base firmly set, insert fixing screws into screw base and 

then into connection holes in toilet base (see illustration).

J. 

Tighten screws and snap on decorative caps.

Sealant or
Plumber’s Putty

Flange

Connection

Holes

Outlet Horn

Decorative Cap     Connection Screw    Base

Tank

Connection

Bolts (2)

Flexible

Supply

Tube

Rubber

Coupling

Gasket

Tank

Connection

Washer (2)

Bottom Tank

Connection

Washer(2)

Nuts (2)

Tank

Connection

Gasket (2)

Tank Flapper

Chain Hook to
be attached to

trip lever

Step 3. Install toilet tank to base.

L.

 Lay tank on clean, stable surface and check 

fittings and handles for tightness. Install rubber 
coupling gasket by pushing onto flush valve stem.

M.

 Connect the flexible supply valve to the supply 

tube and snug this connection by hand.

N. 

Slide washers and rubber gaskets onto tank 

connection bolts and insert bolts through holes in 
tank.

O. 

Lift the tank and set it into place on the base, 

guiding the connection bolts through the holes in 
the base, and the supply tube through its hole.

P. 

While holding tank in position, place washers and 

nuts onto bolts. Tighten nuts evenly until rubber 
coupling gasket forms a tight seal.

DO NOT OVERTIGHTEN BOLTS! BREAKAGE WILL OCCUR! DO NOT USE SEALANTS ON TANK BOLTS, AS THIS WILL VOID THE WARRANTY!

Summary of Contents for MNO490EC






Reviews: