background image

Contact Miseno at (855) 480-2915 or email [email protected] with any questions. Copyright ©2019, Miseno. All rights reserved

PAGE 1

Skirted HET Single- and Dual-Flush Toilet

Installation Instructions

A

B

C

D

E

F

G

H

I

J

Recommended Tools & Materials

Items Included

K

L

M

R&T

IAPMO

A. Screwdriver
B. Adjustable wrench
C. Pencil or marker
D. Tape measure
E. Level
F. Drill
G. Toilet flange

H. Wax ring
I. T-bolts, nuts and washers
J. Supply line
K. Wax ring seal plate
L. Fixing screws and caps
M. Flange connecting brackets

CAUTION: PRODUCT IS FRAGILE

Handle with care to avoid breakage and potential injury

Note: 

Illustrations in this guide are general representations and may not necessarily define the exact contours of the product.

• 

Shut off water supply line to toilet. Flush toilet and remove all water from the bowl and tank using a sponge.

• 

Disconnect the water supply line from the tank.

• 

(OPTIONAL) Remove the tank from toilet base, use a screwdriver, adjustable wrench or socket wrench as necessary.

• 

Loosen toilet bowl flange nuts under bolt caps.  Remove old toilet base by carefully lifting it off the floor.

• 

Clean flange and plug the drain with a rag to prevent sewer gas from escaping.  

Remove rag before placing new toilet.

To remove old toilet:

Floor
Outlet
Flange

12”

(305mm)

T-Connection

Bolts

T-Bolts

Floor
Outlet
Flange

Wax Ring

Flange Seal Plate

T-Bolt Connection Nuts & Washer

Connection Bracket

for Attaching Toilet

to Floor Flange

Seal Plate Assembly

Step 1. Install wax ring seal plate and connection brackets.

A.

 Place two new T-bolts into the slots on the floor outlet 

flange.

B.

 Install the wax ring onto the underside of the wax ring 

seal plate, then press the seal plate down evenly and 
firmly over the T-bolts and floor outlet flange.

C. 

Place the flange connection “L” brackets onto the 

T-bolts then attach the washers and nuts to the T-Bolt (see 
illustration).

D. 

Align flange connection brackets to the sides of the 

seal plate (see illustration) then tighten the nuts 
until snug to seal the wax ring to the floor outlet flange.

Note: 

This mounting assembly assumes your floor outlet 

flange is proud of, or even with your flooring. Recessed 
flanges may not seal correctly and leakage is possible. 
Additional sealing may be necessary in this instance.

Summary of Contents for MNO490EC






Reviews: