background image

12

www.build.com

Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. 
When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust 
from cooking are drawn and 

¿

 ltered by a set of optional charcoal 

¿

 lters. The air is then puri

¿

 ed and re-circulated 

back within the home.

We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct work, 
if possible. The hood is most effective and ef

¿

 cient as an exhaust hood. Only when the exhaust option is not 

possible should you recourse to converting the hood into a recirculating hood.

When converted to be a recirculating hood, a set of charcoal

¿

 lters are required on top of its standard Metal 

Filter set. Order according to its Part number below. The standard Metal Filters are intended to capture residue 
from cooking and the optional charcoal

¿

 lters help to purify fumes exhausted from cooking for re-circulation.

RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED)

Kit includes charcoal 

¿

 lters, charcoal 

¿

 lter brackets and air diverter plate.

Hood Model 

 

Part No. 

          Filters in Pkg.

MH00436G 

                          RHRK004S  

     2                                     

1.   Purchase recirculating kit per the part number above

2.   Secure air diverter plate to top support frame. (FIG. H)  Run 6” ducting 

from top of hood and secure to air diverter plate. 

3.  Remove mesh 

¿

 lters from hood. Secure the charcoal 

¿

 lter bracket to the 

inside of the hood behind mesh 

¿

 lters with (4) M3.5 x 8 screws.  Clip 

charcoal

¿

 lters into each charcoal 

¿

 lter bracket opening. (FIG. H) 

4.   Re-install mesh 

¿

 lters.

5.  Charcoal 

¿

 lters  must  be  replaced  after  every  120  hours  of  use  (or 

approximately every 3 to 4 months based on the average of 1 - 2 hrs. of 
daily cooking time). 

Note:

Refer to manual included with recirculating kit for more detailed 

installation instructions.

Charcoal Filter Replacements

Hood Model 

 

Part No. 

          Qty to Order

MH00436G 

 

RHCF001   

   2

DO NOT WASH CHARCOAL FILTERS.  Charcoal 

¿

 lters may need

to be changed more often depending on cooking habits.

Installation – 

Ductless Recirculating

FIG. H

Summary of Contents for MH00436G






















Reviews: