4
1
Canada
25 Interchange Way, Vaughan, Ontario, L4K 5W3
Tel: (905) 660-4655, Fax: (905) 660-4113
USA
4575 Witmer Industiral Estates, Niagara Falls, New York 14305
Tel Toll Free: (888) 660-4655, Fax Toll Free: (888) 660-4113
Website: www.mircom.com
Alpha Relay Output Module
Installation Instructions
General
The Alpha Relay Output Module, part no MIX-100R, is a loop-powered device which
incorporates a dual form C, volt-free relay output. It is mounted on a plastic fascia
plate for use with a 4" electrical box.
A red LED
fl
ashes in synchronization with the current pulse reply from the device. If
output bit 2 is set, the LED is illuminated continuously.
Note: the Alpha Relay Output Module is not designed for outdoor use unless it is
mounted in a suitable weatherproof enclosure.
Control Panel Compatibility
Compatibility Identi
fi
er number: MIX-100R. The module has been approved by Under-
writers Laboratories Inc. For details of compatible control panels contact Apollo Fire
Detectors Limited.
Installation
These products must be installed in accordance with the applicable NFPA standards,
local codes and jurisdictional authorities. Failure to follow these instructions may
result in failure of devices to report an alarm condition. Apollo Fire Detectors Limited
is not responsible for devices which are improperly installed, maintained and tested.
Before installing these products, check the continuity, polarity and insulation resist-
ance of all wiring. Check that siting is in accordance with the
fi
re system drawings
and conforms to all applicable local codes such as NFPA 72.
1. Mount the electrical box as required and install all cables for termination. Ensure
that cable shield/earth continuity is maintained.
2. Terminate all cables in compliance with local codes and regulations.
3. Set the address of the module as shown on page 3.
4. Drill holes in the fascia plate corresponding to the holes on the mounting box
selected
(Fig 1).
5. Gently push the completed assembly towards the mounting box and align the
fi
xing holes. Secure the unit with the screws provided. Do not overtighten the
screws.
6. Commission the module.
39214-395/Issue 1 Draft B
Note
1. All circuits are power limited except for relay contacts. If the relay contacts are
connected to a non power limited source, remove the lower portion of the power
limited label along the kiss cut. Use only limited energy cable types FPL, FPLR or FPLP
on power limited circuits.
Technical Data
Part No
MIX-100R
Compatability Identifi er
MIX-100R
Type
Relay Output Monitor
Style
Fascia Plate with wiring terminals
Dimensions
4½" x 4½" x 1"
Temperature Range
32°F to 120°F (0°C to 49°C)
Humidity
10 to 93% RH non-condensing
Signal Line Circuit (SLC)
Supervised
Working Voltage
17–28V DC
Modulation Voltage (peak to peak)
9-5V
Supervisory Current
0.85mA
Surge Current
2.5mA
Maximum Alarm Current LED on
3.5mA
Max Line Impedance
50
Ω
max
Functional States
Analog Levels: Normal
16
Relay Output
Non Supervised, dry contact;
24VDC, 2A; 30VAC, 0.5A
Functional Test Data
Output
Bit
Function
Input
Bit
Function
2
Alarm LED
1 = On
0 = Off
2
Alarm LED Con
fi
rmation
1 = On
0 = Off
1
Not Used
1
Not Used
0
Relay Control
1 = On
0 = Off
0
Relay Con
fi
rmation
1 = On
0 = Off
LT-1031 Rev.1
February 2010
