Mircom FR-320 Series Installation And Operation Manual Download Page 39

Page: 39 / 112

9.0

Indicators, Controls and Operations

Refer to Figure 23

below for LED Indicator and Control Button locations.

Figure 23 LED indicators and control buttons

The Main Display Panel on the Main Pre-Action/Deluge and Agent Release Control Board
consists of:

•

16 common LED Indicators (left portion of display)

•

Ten Common Buttons (left half portion of display)

•

Up to six Initiating Circuit Alarm LEDs and six Initiating Circuit Trouble LED Indicators

•

Four Indicating/Releasing Circuit LEDs (labeled NAC for Notifying Appliance Circuit or
RAC for Releasing Appliance Circuit)

•

Up to ten disconnect buttons (six for initiating circuits & four for indicating/releasing
circuits)

LED Indicators may be amber, red, or green, and may illuminate continuously (steady), or at
one of two flash rates.

•

Fast Flash (Supervisory)- 120 flashes per minute, 50% duty cycle

•

Trouble Flash (Trouble) - 20 flashes per minute, 50% duty cycle

Note:

Each display is supplied with laser printer printable paper labels for sliding into
the plastic label template on the panel. For the Main Display, the paper label is

Mircom# NP-2056

. This includes English and French versions.

SYSTEM

RESET

AC ON

GROUND FAULT

CPU FAIL

ABORT

RELEASED

COMMON ALARM

COMMON SUPV

REMOTE TROUBLE

COMMON TROUBLE

BATTERY TROUBLE

SIGNAL

SILENCE

AUXILIARY

DISCONNECT

LAMP

TEST

PRE

RELEASE

RAC2

(ZONE 4)

RAC1

(ZONE 3)

NAC2

(ZONE 2)

NAC1

(ZONE 1)

IAC6

(ZONE 1)

IAC5

(ZONE 5)

IAC4

(ZONE 4)

IAC3

(ZONE 3)

IAC2

(ZONE 2)

IAC1

(ZONE 1)

ALM/SUP/TBL/

BLDG AUDIBLE SIL

Summary of Contents for FR-320 Series

















































































































Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands

Mircom FR-320 Series, Installation And Operation Manual

Search results

Summary of Contents for FR-320 Series

Reviews:

Related manuals for FR-320 Series

Brands by name

Popular brands