Miranda NV5256 User Manual Download Page 24

Page: 24 / 56

Rev 1.7 • 18 Aug 10

3. Detail

Alarms

A redundant reference uses identical, but distinct, reference signals. If one reference source
fails, the other acts as a fail-over.

The NV5256 does not support “dual reference” mode.

If you have an expanded router, use the loop-through connector to connect the master and slave
frames. Terminate any reference chains with 75

terminators.

Time Code Reference

At the lower left portion of the rear of the NV5256 frame are 2 connectors for time-code reference:

The NV5256 does not use time-code reference. You can ignore these connectors.

Alarms

Two alarm connectors (system, and power-supply) allow you to construct alarm indicator circuits
of your own.

System Alarm Outputs

At the lower left portion of the rear of the frame is a female DE9 connector for system alarms:

This connector allows you to create alarm circuits of your own.

The internal alarm signalling is provided by solid-state relays that turn on in the event of an alarm
condition. Table 3-1 describes the individual alarm connections:

ALARMS

TIMECODE

113-128

97-112

81-

145-160

161-176

177-192

193-208

209-224

225-240

241-256

129-144

PORTS

13-

PORT

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

Time-Code

Reference

ALARMS

TIMECODE

13-

PORT

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

13-16

PORT 16

Alarm

Connector

Table 3-1. Alarm Signals

Signal

Description

Possible Alarm Condition(s)

1, 9

Alarm Com

Common

Common connection for all alarm signalling pins. This is a

“return” for an external circuit.

Alarm 1

Major alarm

Missing reference inputs, possible failure of fans or over-
temperature conditions on one or more modules.

Alarm 2

Minor alarm

Any of alarms conditions 3, 4, 5 or 6.

Alarm 3

Power supply

Main power supply module is missing.

Alarm 4

Video reference

Missing video reference signal 1 or 2 (if applicable).

Summary of Contents for NV5256

























































Search results

Summary of Contents for NV5256

Reviews:

Related manuals for NV5256

Brands by name

Popular brands

Miranda NV5256, User Manual

Search results

Summary of Contents for NV5256

Reviews:

Related manuals for NV5256

Brands by name

Popular brands