Miranda NV5256 User Manual Download Page 46

Page: 46 / 56

Rev 1.7 • 18 Aug 10

5. Maintenance

LED Status Indicators

Figure 5-2 shows the location of the fuse on either power supply module.

Figure 5-2. Fuse Location, PS6000 or PS6100 Power Supply

LED Status Indicators

Each I/O card has status indicators (LEDs). Table 5-1 lists the control card’s main LEDs:

250V

Fuse

Table 5-1. Router Control Card LEDs

LED

Function

Description

Red (above

battery holder)

Battery

status

If LED is on, replace battery.

Green

Health

If this LED is on, operation is normal. The control card has successfully
booted. The on-module power supplies are OK. The control card is active

or ready to go active.

Yellow

Active

If this LED is on, the control card is active.

Red

Alarm

If this LED is on, the control card is in a fault state:
Bad or missing video reference or AES reference.
Bad on-module power supply.
Microprocessor failure.

Summary of Contents for NV5256

























































Search results

Summary of Contents for NV5256

Reviews:

Related manuals for NV5256

Brands by name

Popular brands

Miranda NV5256, User Manual

Search results

Summary of Contents for NV5256

Reviews:

Related manuals for NV5256

Brands by name

Popular brands