Minuteman RPM1581EV6 User Manual Download | Manualshive

Page: 19 / 30

background image

18

Configuration: Network

This allows the administrator to configure the network settings.

TCP/IP Settings for IPv4

Host Name:

The host name of the RPM.

DHCP Client:

Enable/Disable DHCP to get the IP address from a DHCP server. The default setting for DHCP

is enabled.

IP Address:

The IP address of the RPM. The default static IP address is 192.168.0.216.

Subnet Mask:

The subnet mask for your network.

Gateway IP:

The IP address of the IVP4 network gateway.

DNS Server1:

The IP address of the primary DNS server.

DNS Server1:

The IP address of the secondary DNS server.

Once the information has been entered click Apply to save the settings.

TCP/IP Settings for IPv6

DHCP Client:

Enable/Disable DHCP to get the IP address from DHCP server. The default setting for the IPv6

DHCP is disabled.

IP Address:

The IPv6 address of the RPM.

Default Gateway Address:

The IP address of the IPv6 network gateway.

Once the information has been entered click Apply to save the settings.

«
...
17
18
19
20
21
...
»

Summary of Contents for RPM1581EV6































Reviews:

No comments

Related manuals for RPM1581EV6

Brand: HP Pages: 13

Brand: HP Pages: 10

Brand: HP Pages: 164

Brand: ABB Pages: 8

Brand: hager Pages: 2

Brand: Panamax Pages: 2

Brand: Panamax Pages: 14

Brand: PortaCo Pages: 22

Brand: OEZ Pages: 6

Brand: Bals Pages: 20

40201S2V4C2A0ES

Brand: Weidmüller Pages: 22

Brand: Ditek Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands