Minuteman F420220-2S Operation Service Parts Care Download Page 6

USER MAINTENANCE INSTRUCTIONS 

A qualified electrician should perform all service and repair. No user serviceable components are 

employed in this equipment. No lubrication of the motor is required. 

CORD STORAGE 

While not in use, storage can be accomplished by winding cord around handle assy. Cord should be 

completely unwound during operation. 

Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return to service center.

Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges
or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

Do not unplug by pulling cord. To unplug, grasp the plug, not the cord.

Do not handle plug or appliance with wet hands.

Always unplug the machine when removing brush. This equipment should be stored indoors and not
exposed to rain.

OPERATION 

The brush is attached in the following manner: Tip machine backward with handle on floor. Brush is then 

inserted over the lugs on the bottom of the gear unit and twisted to the left. This secures the clutch plate 

of the brush over the lugs on the gear unit in the correct driving position. 

LOWER HANDLE ASSEMBLY TO WAIST HIGH POSITION TO OPERATE. 

Due to the rotation of a single disc machine, it will naturally have a tendency to move to the right or left, 

depending on the operator’s slight pressure either up or down on the handle. If the handle is lifted slightly 

up, the machine will travel to the right; a downward pressure and it will travel to the left. It is this 

maneuverability that enables an operator to cover large areas in a short time with the least amount of 

effort. The machine can be made to operate without travel by balancing… 

... KEEPING THE BRUSH PRESSURE ON THE FLOOR EQUAL.

 With a few minutes of 

practice in a large area, you will have perfect fingertip control of the machine. This equipment is 

equipped with trigger safety interlock. Refer to diagram pictured. 

PUSH DOWN

SQUEEZE

SQUEEZE

Summary of Contents for F420220-2S

















Reviews: