MINOURA GYRO V270 Instruction Manual Download Page 1

indoor bicycle trainer 

GYRO V270

instructions manual

Introduction

Thank you for purchasing the Minoura GYRO V270 indoor bicycle trainer.

The V270 incorporates a new, patent pending Gyro Technology flywheel that by design is 35% more 

effective than other trainers in its class.

The new NEODYMIUM (neo-dee-um) magnet is four times stronger than typical ferrite magnets and offers 

a much wider range of resistance from low to high all while providing equal step differentials to simulate 

real road riding.

The exclusive U-SHAPE legs are lightweight but more stable than other trainers weighing much more.

And each leg can be ad/- 10 mm to compensate for uneven surfaces.

Read the is manual carefully and keep it for future reference.

For More Information

MINOURA NORTH AMERICA   

 

 

MINOURA JAPAN HEADQUARTERS

(for U.S. residents ONLY)  

 

 

 

(for ALL customers)

1996 East Ave. Hayward, CA 94541 U.S.A.   

 

1197-1 Godo, Anpachi, Gifu 503-2305 Japan

Phone: 1-510-538-8599 

 

 

 

 

Phone: +81-584-27-3131

Fax: 1-510-538-5899   

 

 

 

 

Fax: +81-584-27-7505

Email: [email protected] 

 

 

 

Email: [email protected]

 

 

 

 

 

 

 

 

Web: www. minoura.jp

MADE IN JAPAN

If you need help, please contact the shop first where you originally 
purchased this product or call the distributors in your own country.
The distributors list can be found on our web site.

Summary of Contents for GYRO V270









Reviews: