background image

9

8

• Do not point the product directly at the sun. If sunlight is focused on

an inflammable surface, a fire may result. Replace the lens cap
when the product is not in use.

• Do not use or store the product in a hot or humid environment such

as the glove compartment or trunk of a car. It may damage the
product and batteries which may result in burns or injuries caused
by heat, fire, explosion, or leaking battery fluid.

• If batteries are leaking, discontinue use of the product.
• Do not fire the flash while it is in contact with people or objects. The

flash unit discharges a large amount of energy which may cause
burns.

• Do not apply pressure to the data panel. A damaged panel may

cause injury, and the liquid from the panel may cause inflammation.
If liquid from the panel makes contact with skin wash the area with
fresh water. If liquid from the panel comes in contact with the eyes,
immediately rinse the eyes with plenty of water and contact a
doctor.

CAUTION

• Immediately remove the batteries and discontinue use if the camera

is dropped or subjected to an impact in which the interior, especially
the flash unit, is exposed. The flash has a high voltage circuit which
may cause an electric shock resulting in injury. The continued use of
a damaged product or part may cause injuries. 

• Keep batteries or small parts that could be swallowed away from

infants. Contact a doctor immediately if an object is swallowed.

• Store this product out of reach of children. Be careful when around

children, not to harm them with the product or parts.

• Do not fire the flash directly into the eyes. It may damage eyesight.
• Do not fire the flash at vehicle operators. It may cause a distraction

or temporary blindness which may lead to an accident.

• Do not look at the sun or strong light sources directly through the

viewfinder or  lens. It may damage your eyesight or cause
blindness.

• Do not use the product near inflammable gases or liquids such as

gasoline, benzine, or paint thinner. Do not use inflammable products
such as alcohol, benzine, or paint thinner to clean the product. The
use of inflammable cleaners and solvents may cause an explosion
or fire.

• If the product emits a strange odor, heat, or smoke, discontinue use.

Immediately remove the batteries taking care not to burn yourself.
The continued use of a damaged product or part may cause
injuries. 

• Take the product to a Minolta Service Facility when repairs are

required.

WARNING

FOR PROPER AND SAFE USE

9222-2163-11 MM-B108 (E).qxd  01.8.3  16:11  Page 8

Summary of Contents for DYNAX 5


























Reviews: