WIRING
DIAGRAM
7
COPILOT
FEA
TURES
INST
ALLA
TION
10
B+
M+
B-
M-
12v
24v
36v
RED M+
BLACK M-
CONTROL
BOARD/
C
A
R
T
E
D
E
C
O
M
M
A
N
D
E
RED
WHITE
FOOT PEDAL
CONTROL BOARD
STEERING MOTOR
BATTERY GAUGE
BATTERY 1
BATTERY 2
B
LA
C
K
B
-
RED B+
COIL
CORD
MOTOR
RED M+
BLACK M-
BLACK
COMPASS
SENSOR
BOARD
BATTERY 1
RT 80 ST is 24-volts only!
BATTERY 1
BATTERY 2
BATTERY 3
BLACK
AUTOPILOT INDICATOR, RED
SYSTEM READY INDICATOR, GREEN
REED SWITCH
AUT
O
PILOT
INDICA
TOR,
RED
(EQUIPPED
MOT
ORS
ONL
Y)
MOMENT
AR
Y
/
CONST
ANT
INDICA
T
OR,
GREEN
ACCESSORY PLUG
SPEED
ADJUSTMENT
KNOB
A
U
T
O
P
IL
O
T
O
N
E
Q
U
IP
P
E
D
M
O
T
O
R
S
O
N
LY
ACCESSORY PLUG
ACCESSORY PLUG
SYSTEM FEATURES
CoPilot for Terrova setup and use instructions
• Your motor is factory installed with CoPilot for Terrova.
• Wireless control for Terrova.
• Plug – n – play design allows for easy hook-up.
• Functions include steering (right/left), prop (on/off), AutoPilot (on/off), high speed bypass, and speed control.
• Receiver mounts into the right side plate of the Terrova motor for seamless installation.
• Patented remote allows motor to be controlled from rod, wrist, belt, or boat console.
• Quick-release rod mounts allow quick and easy transfer of remote from rod to rod.
• Copilot Terrova can be used with or without the corded foot pedal.
• Remote will not interfere with Autopilot or Universal Sonar Operation.
• Up to 10 remotes can be used interchangeably with the same receiver.
• Components are environmentally sealed to protect against rain, wind, or snow.
Installing the rod mount
• The rod mount is designed for installation on any area of the rod grip, especially the area forward of the reel. (See the figures
above.)
• Spinning reel users may want to install the mount on the top of the rod to allow thumb operation of the remote.
• Bait casting reel users who “palm” the reel may install the mount on the side of the rod to allow remote operation with the index or
middle finger.
• The mount should be positioned on the rod so that the unlocking latch on the bracket is toward the rod tip.
1). Position the rod mount in the desired location on the fishing rod, holding it in place with your thumb.
2). Insert (2) tie-down straps through the rod mount and cinch down around the rod (place the locking head of the tie-down
strap to either side of the rod mount; do not place in the area below the remote.)
3). Trim the excess tie down strap with a side cutter or scissors.
• To attach the remote to the mount, slide the remote into the mount from the rear of the bracket. Ensure that the slides on the
mount engage the slots on the sides of the remote. Slide the remote into the mount until it snaps into the locked position.
• To release the remote from the mount, press down on the unlocking latch while simultaneously sliding the remote out of the
mount.
• During periods of non-use, we recommend that the remote be inserted into the mount with the buttons facing down. This will help
to ensure that there are no unintentional button presses while the rod is in storage.
Using the nylon strap with the remote
For a general purpose strap mount, refer to the figure above. This strap can be used as a wrist mount, around the belt, to a fixed
location on the boat, etc…
SPINNING REEL
BOBINE ROTATIVE
BAIT CASTING REEL
BOBINE À JETER L’APPÂT
IN
ENTRÉE
OUT
SORTIE
Summary of Contents for Riptide 80 ST
Page 2: ......
