©2020 Johnson Outdoors Marine Electronics, Inc.
a. Retract the anchor
on the Raptor Pump
by pressing the Up
button on the
Raptor Indicator Panel.
Once the Raptor is
fully retracted, press
and hold the Up
button and the Down
button on the
Foot Switch at the same time until the Raptor
Selection
and Mode
LED's at the top of
the Foot Switch begin to scroll. Then release them.
b. Immediately press the Pair
button on
the Indicator Panel. The Pair LED on the
Indicator Panel will flash blue
. The Raptor
and Foot Switch will go into Pairing Mode for
20 seconds. If a signal with three fast beeps
occurs, the Raptor and Foot Switch have
successfully paired. If 20 seconds pass while
in Pairing Mode and they do not successfully
pair, an error tone will sound indicating that the
pairing was not successful, and the Foot Switch
will not be able to control the Raptor.
c. If the Pair is unsuccessful, repeat the process.
minnkotamotors.com
Installation Parts List
Mounting Considerations
Tools and Resources Required
Installation
a. Review the Mounting
Considerations to
determine an
acceptable mounting
location. Once a
location is selected,
take the Raptor Foot
Switch Assembly
(Item #A) and
remove the Pedestal
from the Base by
squeezing the Tabs
on both sides of the
Foot Pedal and
pulling the Foot Switch and Pedestal apart.
Foot Switch
Pedestal
Marked Location
Mounting
Holes
Pads
Pedestal
(top)
Pedestal
(bottom)
Tab
Tab
FOOT SWITCH
b. The Pedestal has three Mounting Holes that
are used to secure it to the boat. The bottom
side of the Pedestal has three Pads around the
NOTICE:
The Pedestal comes attached to
the Foot Switch and needs to be removed
for installation.
NOTICE:
For instructions on how to pair
two Raptors and assign their Port and/or
Starboard mounting locations, please refer
to your Raptor Owner’s Manual.
Mounting Holes
Pedestal
c. Double check the
Mounting Location.
Take the Screws
(Item #2) and place
one each in the
Mounting Holes of
the Pedestal. Make
sure the Mounting
Holes line up with
the Marked Locations
and then use a Drill
with #2 Phillips
Driving Bit to secure
the Pedestal to the
Deck of the Boat. Do
not over-tighten.
Deck
of Boat
Deck
of Boat
Screws
Pedestal
Tab
Foot Switch
Tab
d. Once the Pedestal
is installed, take the
Foot Switch and
reattached it to the
Pedestal. Make sure
the Tabs on the Foot
Switch click into
place and the Foot
Switch is fully seated
on the Deck of
the Boat.
Up Button
Pair Button
Pair LED
Indicator Panel
Single press to display the current operating
speed. While the speed is displayed,
continue to single press through the
operating speed to toggle between slow,
medium and fast. The Mode LED
will
flash red three consecutive times at the
speed that corresponds with the selected
speed. Pressing and holding the button
will toggle the remote to control either
the Port, Starboard or both anchors when
two anchors are paired in the system. The
Raptor Selection LEDs will illuminate
to correspond to the anchor(s) selected.
The right LED will illuminate when the
Starboard anchor is selected and the left LED
will illuminate when the Port anchor is
selected. Both the right and left LEDs
illuminate when both anchors are selected.
Auto Down
Button/Pairing
Button
Auto Up
Button/
Pairing
Button
Anchor Mode
Button
Raptor Selection
Button/Speed
Button
Raptor Selection
Indicator LEDs
Anchor Mode
Selection LED
RAPTOR WIRELESS FOOT SWITCH
QUICK REFERENCE GUIDE
1810258
Compatible with Bluetooth
®
enabled Raptor Systems only.
Your new Raptor Foot Switch comes complete with
all of the hardware you’ll need to install it directly
to the deck of your boat. Please review the parts
list, mounting considerations and tools needed for
installation prior to getting started.
Item /
Assembly
Part #
Description
Qty.
A
2994155
FOOT SWITCH ASM,
RAPTOR
1
2
2383455
SCREW-#8 X 1.0"
PPH TY AB SS
3
Before mounting your Raptor Foot Switch, please
give consideration to the following:
a. Examine your boat to ensure that you will
not drill into any obstructions and that the
hardware will be accessible for assembly.
b. Make sure the area under the mounting
location is flat, clear to drill holes and that the
installation hardware will not damage existing
components below the mounting surface. It
may be necessary to shim or modify the
mounting surface under the mounting location
to create a flat area for the Foot Switch
Pedestal to be mounted.
c. Mount the Raptor Foot Switch in an area that
has a clear line of communication with the
Bluetooth enabled Raptor(s) it is intended to
control for optimum performance.
d. Mount the Raptor Foot Switch in an area
where it will not become a tripping hazard.
• Pencil or similar marking tool
• Drill
• #2 Phillips Driving Bit
INSTALLING THE FOOT SWITCH
PAIRING THE FOOT SWITCH
Scan to view the complete
Raptor Foot Switch Manual
online. The Owner's Manual is
available at
and includes information
on compatibility, safety
considerations, compliance,
maintenance, parts and more.
Single press to auto retract the anchor. Press
and hold to continually retract the anchor.
The anchor will continue to retract when the
button is held until the button is released.
Double press to auto deploy the anchor.
Double press and hold the second press to
continually deploy the anchor. The anchor
will continue to deploy when the button
is held until it reaches its full range of
operation or until the button is released.
Single press to display the current Anchor
Mode. While the mode is displayed,
continue to single press through the
Anchor Modes to change them. This
will toggle through the Anchor Modes of
Normal, Rough Water, Soft Bottom and
Auto Bottom. Normal Mode is identified
when the Mode LED
flashes
between red and green. Rough Water
mode is identified when the Mode LED
flashes red and Soft Bottom when the
Mode LED
flashes green. Auto Bottom
Mode is only available on the Pro Model
and is identified by a Mode LED
that flashes slowly from green to green
and then red to red. On the Pro Model, the
Anchor Mode button will also enable and
disable Active Anchoring. Active Anchoring
is engaged and disengaged by a single
press and hold. When the Mode LED
displays green it is enabled and when the
Mode LED
displays red it is disabled.
Auto Up Button
Auto Down Button
Anchor Mode Button
Speed Button / Anchor Selection Button
Mounting Holes. These Pads should be placed
down, towards the boat when the Pedestal is
installed. Position the Pedestal at the selected
location and mark the Mounting Holes with a
pencil or similar marking tool.
