MinimumRC F6F Hellcat Page 1 Assembly Instructions Manual Download | Manualshive

Page: 1 / 18

background image

F6F Hellcat Q-Series

Assembly Instructions

Important notification

1.The model is supplied with UFO and 502 glue. UFO is for bonding foam parts, and 502 for

bonding wood, carbon fiber and metal parts. 502 glue will cause serious corrosion to foam parts.
2.Please wait for the glue to dry and solidify in each installation step before the next installation.

3.Please avoid using flame to heat the heat shrinkable tube on the model. Electric iron shall be
used for heating.
4.Please use razor blade to remove the parts from the plate. Do not tear the parts by force.

1
2
3
...
»

Summary of Contents for F6F Hellcat



















Reviews:

No comments

Related manuals for F6F Hellcat

Cult Sport 2009

Brand: Naish Pages: 43

Brand: Quickie Pages: 84

Brand: Team 5 Pages: 100

Brand: Beechcraft Pages: 51

Brand: MAC PARA Pages: 32

Samba R.E.S. Evo

Brand: cad2cnc Pages: 33

Brand: Malibu Boats Pages: 2

Brand: Magni Gyro Pages: 105

Brand: Schempp-Hirth Pages: 11

Brand: THUNDER TIGER Pages: 8

ARCHER II PA-28-181

Brand: Piper Aircraft Corporation Pages: 117

Brand: Opale-Parmodels Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands