8. Once the hook is in place, let the mat and hook
rest on the loor as shown in Figure 6. Next,
conirm that the mat is not interfering with foot
pedals and verify it is making proper contact with
the surfaces surrounding the loor.
9. Mark the approximate position where the hook
will need to be attached to the loor with a inger.
Once the position is located, remove the driver
mat from the truck.
10. Unpack the tube of Primer 94 and read the
safety precautions printed on the tube.
11. Activate the tube of Primer 94 by crushing the
tube at the black dot.
12. Clean all dirt or debris off the truck loor and
apply Primer 94 to the truck loor area where the
hook will be attached.
13. Allow the Primer 94 to dry on the truck loor
for ive minutes.
14. Install the driver mat in the truck with the
hook inserted. Next, peel away the paper backing
from the hook.
15. While holding onto the neck of the hook, lower
the driver mat into position and stick the hook
to the loor. Apply irm pressure to the hook as
shown in Figure 7 for 30 seconds to ensure a
proper bond to the rubber loor.
16. For optimal adhesion do not disturb the hook
for a period of 20 minutes after installation.
17. Install the center mat as shown in Figure 8
below.
18. Install the passenger mat and driver mat.
Note: the passenger side loor mat is designed to
accommodate both ixed seats and suspension
seats. For trucks equipped with a ixed passenger
seat, there will be a gap of approximately 1.5
inches between the base of the seat and the back
edge of the passenger loor mat.
19. Pull the driver mat toward the front of the
truck to conirm that the hook is fully engaged
into the mat and that the hook is adhered to the
loor. If the hook is not functioning properly or
the mat cannot be securely installed, do not use
a Minimizer loor mat on the driver side of the
vehicle.
20. FAILURE TO PROPERLY INSTALL THE RETENTION
HOOK FOR THE DRIVER SIDE FLOOR MAT MAY ALLOW
THE MAT TO SHIFT, WHICH MAY INTERFERE WITH
PROPER FUNCTIONING OF THE VEHICLE’S PEDALS,
POTENTIALLY RESULTING IN LOSS OF CONTROL OF
THE VEHICLE AND SERIOUS INJURY OR DEATH.
Minimizer loor mats are speciically designed
for certain vehicles and may be used safely
only with those vehicles. VERIFY THAT THE
MAKE, MODEL, AND YEAR OF THE VEHICLE IN
WHICH YOU ARE INSTALLING THE FLOOR MATS IS
IDENTIFIED ON PAGE 1 AS BEING COMPATIBLE
WITH THE MINIMIZER FLOOR MATS YOU HAVE
SELECTED.
VOLVO FLOOR MAT MODELS ARE AVAILABLE FOR BOTH
MANUAL AND AUTOMATIC TRANSMISSIONS:
• Kit #
FKVOLVO1MB
shown below in Figure 1 is
compatible with Volvo trucks equipped with a
manual transmission.
• Kit #
FKVOLVO1AB
shown below in Figure 2 is
compatible with Volvo trucks equipped with an
automatic transmission.
INSTALLATION INSTRUCTIONS
1. Remove other loor mats from the vehicle
before installing Minimizer loor mats.
2. Install the Minimizer loor mats right side up,
with the Minimizer logo visible.
3. Each Minimizer loor mat is contoured to it
a particular location in the vehicle and may be
used safely only in that location.
4. The Minimizer loor mat package contains
one driver mat, one passenger mat, and one
center mat that its in between the seats.
5 . Position the driver mat in the truck as
shown in Figure 3.
6. Inside the package with the installation
instructions, locate the black plastic retention
hook as well as a white tube of Primer 94 as
shown in Figure 4.
7. Insert the hook up through the hole at the
right rear corner of the driver side loor mat as
shown in Figure 5. The hook should it lush with
the underside of the loor mat.
Figure 5 - Hook Insertion
Figure 4 - Hook and Primer 94
Figure 1 - Kit FKVOLVO1MB
Figure 6 - Conirm Location Driver Mat and Hook
Figure 2 - Kit FKVOLVO1AB
Figure 7 - Apply Pressure to Hook
Figure 8 - Center Mat Installed
Figure 3 - Driver Mat in Position
