Minebea Intec Maxxis 5 Phase PR 5900/81 Operating Instructions Manual Download Page 58

Page: 58 / 94

7.3.4

Production Started on the Device

Production can be started, stopped, resumed or canceled on the device.

Requirements, see Chapter

7.3.4.1

Procedure, see Chapter

7.3.4.2

7.3.4.1

Requirements

The production line has been loaded under [Coniguration] - [Production lines] and

activated (in this case: PL 1).

The parameters for local operation have been selected under [Coniguration] - [Local

control] .

7.3.4.2

Procedure

Scale-A

Scale-B

Free

Gross

Free

Gross

0.3 g

595 kg

Recipe

Scale-A

Scale-B

Free

Gross

Free

Gross

0 g

595 kg

Recipe

Select recipe function.

Start

1. Press the [Recipe]/[Plan] soft key.

A prompt window appears.

2. Press the [Start] soft key.

A selection window appears.

Phase PR 5900/81

7 Operation and visualization of the scales

EN-56

Minebea Intec

Summary of Contents for Maxxis 5 Phase PR 5900/81































































































Search results

Summary of Contents for Maxxis 5 Phase PR 5900/81

Reviews:

Related manuals for Maxxis 5 Phase PR 5900/81

Brands by name

Popular brands

Minebea Intec Maxxis 5 Phase PR 5900/81, Operating Instructions Manual

Search results

Summary of Contents for Maxxis 5 Phase PR 5900/81

Reviews:

Related manuals for Maxxis 5 Phase PR 5900/81

Brands by name

Popular brands