Minebea Intec CAS1 Operating Instructions Manual Download Page 29

Page: 29 / 160

Aggressive chemical vapors

Extreme moisture

Extreme vibrations

4.2.3

Unpacking

The following applies for devices from a platform size of 60 x 80 cm:

4.2.4

Checking the equipment supplied

Indicator

Weighing platform

Operating instructions 98628-000-71

Options (special equipment) as noted on the delivery note

4.2.5

Remove transport locks

CA…G-…IG-… models (see chapter

4.2.5.1

)

CA…G-64-FE-… models (see chapter

4.2.5.2

)

4.2.5.1

CA…G-…IG-… models

Remove transport locks.

Wear protective clothing (safety shoes and, if necessary, gloves)

When lifting or transporting the weighing platform, always lift it by its longest sides.

Unpack the device and check it for visible external damage.

If there is damage, follow the instructions in the chapter

9.4

"Safety check".

Keep the original packaging in case the device needs to be returned. Remove all

cables before sending.

1. Place the weighing platform at its installation location, remove the weighing pan.

4 Device installation

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

Minebea Intec

EN-27

Summary of Contents for CAS1

































































































































































Search results

Summary of Contents for CAS1

Reviews:

Minebea Intec CAS1, Operating Instructions Manual, Page: 29 / 160

Search results

Summary of Contents for CAS1

Reviews: