Mimosa 0151858 Manual Download Page 5

610mm

for JDS04

610mm

CEILING

WA

L

L

480 mm

480 mm

The heater is for outdoor use only. Always ensure that adequate fresh air 
ventilation is provided.
Always maintain proper clearance to combustible materials, i.e. top 480mm 
and sides 480mm minimum.

Any enclosure in which the appliance is used shall comply with one of 

the following:

An enclosure with walls on all sides, but at least one permanent opening 

at ground level and no overhead cover.

Within a partial enclosure that includes an overhead cover and no more than two walls.

Within a partial enclosure that includes an overhead cover and more than two walls, 

the following shall apply:

   at least 25% of the total wall area is completely open, and

   at least 30% of the remaining wall area is open and unrestricted.

In the case of balconies, at least 20% of the total wall area shall be and remain open 

and unrestricted.

Never operate heater in an explosive atmosphere like in areas where
petrol or other flammable liquids or vapors are stored.
This appliance shall only be used in an above ground open-air situation 
with natural ventilation, without stagnant areas, where gas leakage and 
products of combustion are rapidly dispersed by wind and natural convection.
This appliance shall be used only in an outdoor area and shall not be used 
in a building, garage or any other enclosed area unless the enclosure meets 
the requirements outlined in this instruction manual.

Heater must be placed on level firm ground.

DIAGRAMMATICAL REPRESENTATIONS OF OUTDOOR AREAS

The following figures are diagrammatical representations of outdoor areas as described above.
Rectangular areas have been used in these figures - the same principles apply to any other
shaped area.

(Informative)

Heater Stand and Location

Page 2

Summary of Contents for 0151858

















Reviews: