3
SPECIFICATIONS
Cat. No. ........................................................... MPS
Max pipe size.........................................152mm (6")
ASSEMBLY
WARNING
Only use accessories specifically
recommended for this tool. Others
may be hazardous.
Inspect the pipe stand and screws periodically
and replace immediately if cracked, worn, or
damaged. Do not attempt to fix or mend damaged
pipe stand or fasteners.
Setting up Stand
out of the areas where the legs will
secure into place.
port stand.
1. Make sure area is dry, stable and level to sup-
the t-bar foot resting on the ground.
2. Hold the stand with the tabletop chest-high with
Fingers can be pinched between the
legs and the underside of the tabletop.
To reduce the risk of injury, keep fingers
3.
4.
Place one hand behind the chain vice and other
hand on the bottom of the tabletop under the leg
locking fold latch.
Place one foot on top of the t-bar foot. With the
hand gripping under the latch, pull and hold the
latch to release the legs.
5. Push chain vice down and away while lifting the
back of the tabletop with the hand gripping the un-
derside of the latch until the stand is fully deployed.
NOTE:
By letting the whole system pivot around
t-bar foot the stand will fully deploy.
the Stand
1.
Collapsing
including
workpieces
the
the stand.
on
6. Once stand is fully deployed, guide the turnbuckle
toward the leg to lock into place (as shown in im-
age above).
7. Hand tighten the turnbuckle to lock and take up
any slack in the stand. Do not use a wrench or
pliers to tighten the turnbuckle.
8. Use level adjuster, if needed to make adjustment to
the level of the table to achieve your desired angle.
2. Release the turnbuckle.
foot.
top of
3. Place one foot
the t-bar
on
vice and other
Remove all tools and
lower shelf o
ff
tabletop
the chain
NOTE:
pinched by
4. Place one hand behind
hand on rear handle.
can
while collapsing.
be
Fingers
turnbuckle
reduce the risk
not place
the
image below)
To
rear handle.
(pinch points shown
of injury, do
in
hand
centre of the
in
Pinch point
Latches
while
5. Pull the chain vice
towards the body
pushing
down
up
away
the other
until the
legs lock into the
hand
to
Ground
and
latch.
Mounting the Stand
1.
the
is installed on a flat, smooth
Make sure the stand
level surface (ground).
the legs.
in
3. Remove the rubber caps on the bottom
the
and
the ground
4. Use M8 screws to
2. Unscrew the bolts
t-bar leg pads.
mount to
with
Make
screws are
legs provided.
sure
during use.
Periodically check that screws are tight.
OPERATION
holes in
secure
NOTE
:
injury, always
marked
WARNING
To reduce the risk of
Attaching Pipe to stand
wear proper eye protection
to comply with AS/NZS 1337.1.
Loosen chain and place chain on the chain tighten-
1.
ing handle
2.
down on jaw and
side of the jaw.
Place pipe
secondary
the material being secured is
support if
long enough to reach
to the secondary support.
4.
3. Move chain over pipe through slot on left side.
pipe with tightening handle.
tighten vice handle with a
Tighten chain around
NOTE:
Do not over
stand is modi-
fied and a cheater bar is used the vice assembly
cheater bar, only hand tighten. If
may fail.
ACCESSORIES
WARNING
ries. Others may be hazardous.
Use only recommended accesso-
For a complete listing of accessories, go online to
milwaukeetool.com.au/ milwaukeetool.co.nz or
contact a distributor.