Milwaukee M18 FUEL FDD3, Operator'S Manual, Page: 4 / 8

4
2. To remove the side handle, loosen the side handle
grip until the side handle can be removed. Reposi-
tion and tighten securely.
;
Correct
:
Incorrect
WARNING
Always remove battery
changing or removing
pack before
accesso-
ries. Only use
mended for
-
Installing Bits
this tool. Others may be hazardous.
Always remove or the battery before inserting remov-
ing bits. Select size bit the proper style and for the job.
This tool is chuck The
can be tightened with one hand, creating
equipped with a spindle lock.
higher grip
strengths on the bit.
To 1. open the in the
counterclockwise direction.
chuck jaws, turn the sleeve
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck’s operation.
FUNCTIONAL DESCRIPTION
1. LED
2. AUTOSTOP™ light
3. Trigger
4. Keyless chuck
5. Torque selector collar
6. Speed selector
7. Side handle
11. Bit holder
8. Control switch
9. Handle
10. Belt hook
ASSEMBLY
WARNING
Recharge only with the charger
-
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Hooks
Slots
WARNING
reco
Only use
mmended
accessorie
for thi
s
s tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using this tool. Always brace or
hold securely. Ensure side handle is tightened
securely before each use.
Installing the Side Handle
1. To install the side handle,
loosen the side handle
grip until the hooks are far
slots on the gear case
ring. Position the side
handle on the top, pointing
to the left or right. Tighten
the side handle grip until
it is secure.
WARNING
the battery pack
Always lock the trigger or remove
any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Volts........................................................... 18V DC
SPECIFICATIONS
Battery Type .................................................M18™
Charger Type................................................M18™
Recommended Ambient
Operating Temperature ................... -17°C to 51°C
Cat. No. ................................................ M18 FDD3
No Load RPM ........... Low 0 - 500 High 0 - 2100
Peak Torque .............................................. 158 Nm
Steel ............................................................ 13 mm
Wood Flat Bit ............................................ 38 mm
Auger Bit ......................................... 38 mm
Hole Saw ........................................ 89 mm
Screws (dia.)................................... 15 mm
Self Feed Bits ................................. 65 mm
Cat. No. ................................................. M18 FPD3
No Load RPM ........... Low 0 - 500 High 0 - 2100
BPM ................................................High 0 - 33,000
Peak Torque .............................................. 158 Nm
Steel ............................................................ 13 mm
Wood Flat Bit ............................................ 38 mm
Auger Bit ......................................... 38 mm
Hole Saw ........................................ 89 mm
Screws (dia.)................................... 15 mm
Self Feed Bits ................................. 65 mm
Masonry ...................................................... 15 mm
When using drill bits, allow the bit to strike the
bottom of the chuck. Centre the bit in the chuck
jaws and lift it about 1.5 mm off of the bottom.
3
4
5
6
8
1
7
9
10
2
11