4
OPERATION
WARNING
1.
Resisting Threading Forces
2.
Support
Arm
3. Place the tool with installed
die head over the pipe.
4. Slide the support arm
through the tool’s sup-
port arm bracing point.
5. Continue to slide the tool over
the pipe until the end of the
pipe contacts the cutting dies
in the die head. The support
arm will be inside the tool’s
bracing point.
SPECIFICATIONS
Cat. No. ............................................. M18 FPT114
Volts........................................................... 18V DC
Battery Type .................................................M18™
Charger Type................................................M18™
Capacity .............. 1/8" - 1-1/4" (3.2 mm - 31.8 mm)
Die Head.
MILWAUKEE
®
11-R series or equivalent
No Load RPM ................................................ 0 - 35
Recommended Ambient
ASSEMBLY
Operating Temperature .................... -18°C to 51°C
WARNING
Removing/Inserting the Battery
To
remove
the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
the battery pack
Always lock the trigger or remove
any time the tool
is not in use.
To
insert
the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
reco
Only use
mmended
accessorie
for thi
s
s tool. Others
may be hazardous.
Installing/Removing Die Heads
.
l
o
o
t
e
h
t
f
o
e
d
i
s
r
e
h
ti
e
m
o
r
f
d
e
t
r
e
s
n
i
e
b
n
a
c
d
a
e
h
e
i
D
1. Remove battery pack.
2. Rotate the die head lock ring to
the unlocked position.
3. Rotate the die head lock ring
to lock. The lock ring will click
when locked.
4. Always check the die head
is locked into the tool before
starting a cut.
ONE-KEY™ Indicator
Solid Blue
Blinking Blue
Wireless mode is active and ready
app.
Tool is actively communicating with
the ONE-KEY™ app.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
Blinking Red
Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
FUNCTIONAL DESCRIPTION
9
11
10
12
1. Side grip
2. Die head lock ring
3. Support arm bracing point
4. Carry handle
5. ONE-KEY™ indicator
6. Internal battery
7. Trigger
8. Control switch
9. Support clamp
1
3
4
5
7
8
2
6
10. Tightening arm
11. Support arm
12. Jaws
5. To remove, unlock the die head lock ring and pull
the die head from the tool.
To reduce the risk of injury,
always wear proper eye
protection marked to comply with
AS/NZS 1337.1.
Recharge only with the charger
specified for the battery. For
specific charging instructions, read the
operator’s manual supplied with your charger
and battery.
WARNING
Loss of control during operation can
result in personal injury.
WARNING
Do not
attach the
tool to the support arm in
any other location.
When threading or backing die head off pipe,
firmly hold the tool to resist forces regardless of
support device used. This will reduce the risk of
striking, crushing and other injuries.
Always use the support device provided with
the tool. Loss of control during operation can
result in personal injury.
Always use the support clamp provided with the
tool. The support clamp attaches to the pipe and
helps to resist the threading forces.
Position the support clamp
jaws around the pipe. To
properly locate the support
arm for threading, the
support arm should be
parallel to the pipe and the
end of the support arm
should align with the end of
the pipe.
Turn the tightening arm to
firmly secure the support
clamp on the pipe.
