9
tool may stall or overheat the motor.
9. After the cut is complete, release the trigger and
wait for the blade to stop completely. Raise the
saw head and remove the workpiece.
WARNING!
If small cut-off pieces get caught in the guard area,
remove battery pack before clearing.
Making a Sliding Cut (Cross Cut)
Wider workpieces can be cut using the sliding
mechanism. Always use chop cut whenever possible.
4
2
3
1
1. Make sure that the chop lock is unlocked, the
slide rail transport lock is loose, and the saw head
moves freely back and forth.
2. Select the desired angles and adjust the fences to
ensure fence hand holds are positioned to keep
hands out of the No Hand Zone.
3. Place the workpiece on the turntable and line
up the cut.
4. Insert battery pack.
5. Support the workpiece using any of the methods
described in "Support the Workpiece Properly".
6. WARNING!
Keep hands out of the No Hands
Zone at all times during use. Contact with blade
will result in serious injury.
7. Raise saw head and pull it out OVER the work-
piece WITHOUT cutting.
8. Start the motor. Wait a few seconds for the blade
to reach full speed.
WARNING!
Do not allow
the blade to contact the workpiece while tool is
ramping up.
9. Press down on saw head.
10. Push saw through the cut.
WARNING!
Return saw
head to the full rear position after each crosscut
operation.
11. After the cut is complete, release the trigger and
wait for the blade to stop completely. Raise the
saw head and remove the workpiece.
WARNING!
If small cut-off pieces get caught in the guard area,
remove battery pack before clearing.
APPLICATIONS
WARNING
'RQRWFXWVWRQHEULFNFRQFUHWH
magnesium, or ferrous metals
(iron, steel, stainless steel, or alloys of these
metals) with this saw.
'RQRWXVHDEUDVLYHZKHHOVZLWKWKLVVDZ
'XVWFUHDWHGE\FXWWLQJWKHVHPDWHULDOVDQGRU
XVLQJDEUDVLYHFXWRIIZKHHOVFDQMDPWKHEODGH
JXDUGDQGSRVVLEO\FDXVHSHUVRQDOLQMXU\
•
Wood -
solid wood, plywood, particle board, MDF
PHGLXP GHQVLW\ ¿EH') KLJK GHQVLW\
¿EHUERDUG PHODPLQH ODPLQDWHG SDUWLFOH ERDUG
formica laminates, hardboard (masonite).
•
Plastics -
PVC, CPVC, ABS, solid surfacing materi-
als (such as Corian
®
), and other plastic materials.
When cutting plastic, avoid overheating the blade
and blade teeth to prevent melting the workpiece.
•
Nonferrous Metals -
aluminum, brass, copper, and
other non-ferrous materials.
&XWWLQJ1RQ6TXDUH0DWHULDOV
Cutting Round (Cylindrical) Materials
"V" shaped blocks can be used to support round
materials like closet rod and plastic pipe.
Aluminum Sash and Other
Channel Type and Materials
Aluminum sash material can be supported with blocks
to prevent it from deforming while it is being cut.
Clamp
Fence
7DEOH
Wood support
block
Aluminum
material
Wood support
block
Mitr
H
Range
Mitr
H
Detents (Stops)
0° to 50° Left
0° to 60° Right
0°, 15°, 22.5°, 31.62°, 45°, 50° Left
0°, 15°, 22.5°, 31.62°, 45°, 60° Right
Bevel Range
Bevel Detents (Stops)
0° to 48° Left
0° to 48° Right
0°, 22.5°, 33.85°, 45°, 48° Left
0°, 22.5°, 33.85°, 45°, 48° Right
Base Molding
Capacity
Nested Crown
Capacity
PP
at 0°
PP
at 45° Left
PP
at 45° Right
PP
Recommended Materials and Applications
Recommended Materials and Applications The
following materials can be cut with the com-pound
sliding mitre saw. There are many types of saw
blades available. Always use the proper blade for
the particular material and application.
Use only
254 mm (10") sliding mitre saw blades rated at least
4000 RPM.
