Milwaukee 4933459732, Original Instructions Manual, Page: 10 / 11

18 19
Oil, dirt, rust or other matter on the threads or under the
head of the fastener aff ects the degree of tightness.
The torque required to loosen a fastener averages 75% to
80% of the tightening torque, depending on the condition of
the contacting surfaces.
On light gasket jobs, run each fastener down to a relatively
light torque and use a hand torque wrench for fi nal
tightening.
DRIVE CONTROL
The drive control button is used to adjust the torque, rotation
speed (RPM), and impact speed (IPM) for the application.
To select the drive control mode:
1. Pull and release the trigger to turn on the tool. The
current mode indicator is lit.
2. Press the drive control button to cycle through the
modes. Select wireless to change the default settings via
the ONE-KEY™ App on your smart device. When the
desired mode indicator is lit, begin work.
NOTE: Select the torque range in accordance with the
equipment manufacturers fastening instructions.
For precision applications, confi rm the fi nal tightening torque
with a calibrated device.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool,
please reference the Quick Start guide included with this
product or go to www.milwaukeetool.com/one-key. To
download the ONE-KEY app, visit the App Store or Google
Play from your smart device.
When the product experiences ESD, the speed LED shuts
down and the product cannot adjust speed. It needs the
battery and coin cell removed and reinserted to recover (see
page 6 & 16).
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset
manually to recover.
We considered the results to be within our minimum
acceptable performance level according to EN 55014-2 / EN
301489-1 / EN 301489-17.
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, after use, the battery packs have
to be fully charged.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate
for about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the
battery could become to high. If this happens, the battery
will shut down.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Refer to the ONE-KEY App for information regarding
necessary servicing.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
ENGLISH ENGLISH
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Do not swallow the coin cell battery!
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
n
0
No-load speed
IPM
Impact range
V Volts
Direct current
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark