Milnor E-P Plus Reference Download Page 52

Page: 52 / 92

Pellerin Milnor Corporation

This procedure replaces field-modified wash formulas with the standard formulas provided
by Milnor

•

YES: Continue to step 3

•

NO: Skip to

1.: step 1, Part C, page 46

3. Enable

Program

Turn the

Run/Program

keyswitch to set the controller to the

Program

mode.

4. Select and Enable

Standard Formulas

Scroll to

Standard Formulas

(item 3 of the

Program Menu

), then confirm the selection.

5. Clear formulas 11 - 30?

Do you want to

keep

clear

formulas 11 through 30?

•

YES: Continue to step 6

•

NO: Skip to

1.: step 1, Part B, page 46

Select and Confirm

Default 30 Formulas

Continue with this procedure to replace formulas 1 through 10 with the standard formulas and
erase formulas 11 through 30.

7. Standard formulas written to memory

The controller will pause for a few seconds while the standard formulas are written to the con-
troller memory.

8. Return to

Run

mode

When the display becomes active again, turn the

Run/Program

keyswitch to the

Run

position.

9. End

2.3.5.2

Part B

BNCJUP02.T02 0000191349 C.2 D.2 A.5 1/2/20 1:16 PM Released

1. Abandon operation?

Abandon this operation to retain all current formulas.

•

YES: Skip to

1.: step 1, Part C, page 46

•

NO: Continue to step 2

2. Select and Confirm

Default 10 Formulas

Continue with this procedure to replace formulas 1 through 10 with the standard formulas,
but keep all programmed formulas from 11 through 30.

3. Return to

7.: step 7, Part A., page 46

2.3.5.3

Part C

BNCJUP02.T04 0000191850 C.2 D.2 A.4 1/2/20 1:16 PM Released

1. Terminate process

Programming

Summary of Contents for E-P Plus





























































































Search results

Summary of Contents for E-P Plus

Reviews:

Milnor E-P Plus, Reference, Page: 52 / 92

Search results

Summary of Contents for E-P Plus

Reviews: