Miller Compass 25 Operator'S Manual Download Page 5

 

5

7

1

  

(2

.8)

16

3 (

6

.4

)

19

0 (7

.5

)

175 (6.9)

HEIGHT

ABOVE BOWL

165 (6.5)

90 (3.5)

Ø100 (3.9)

Ø 98 (3.9)

102  (4.0)

 

 

Weight 2.8 

kg 

Payload Range 

4.0 – 14.0 kg 

Max.Payload Capacity 

20 kg 

Tilt Drag 

5 Selectable fluid drag pos 0 

Tilt Range 

+ 90˚ / -75˚ 

Tilt Lock 

Positive Lock caliper brake system 

Pan Drag 

5 Selectable fluid drag pos 0 

Pan Range 

360˚  

Pan Lock 

Positive Lock caliper brake system 

Counterbalance System 

4 Selectable positions (see 
performance graph) 

Camera Platform Type 

Sliding platform with 70 mm travel & 
quick release Euro Camera Plate. 

Camera Plate 

1/4”, 3/8” and 1/4” + Pin Carriage 

Mounting Base 

Ø100 mm Ball Levelling 

Ball Level Range 

10˚ 

Handle 

Standard black anodised pan 
handle with adjustable angle. 

Temperature range 

-40˚ C to +65˚ C 

Construction 

Lightweight diecast Aluminium 
alloy, moulded reinforced plastics 

Sealing 

Water & Dust resistant 

Finish 

Matt black (low sheen) durable 
powder coated with anti-corrosive 
pre treatment 

Warranty 3 

Years. 

Technical Data 

Summary of Contents for Compass 25













Reviews: