Miller 1078 Arrow fx 3 Operator'S Manual Download Page 4

43

Thank you for purchasing the Arrow

 fx

 fluid head. 

This Miller product provides the user precise pan and tilt 

coordinates through seperated (pan and tilt) outputs. These 

outputs can be coupled with other equipment data to provide 

augmented visual effects during broadcast and production. 

The Arrow

 fx

 has been designed to suit a wide range of cameras, 

lenses and accessories as demanded by ENG, EFP, Studio and 

Field OB setups.

The robust design and construction of the Arrow

 fx

 fluid head 

offers maximum stability, accuracy and durability and includes 

precision ball bearing mounted fluid drag plate system in the pan 

and tilt assembly to deliver true fluid drag performance over the 

entire temperature and payload range. 

The fluid drag and the counterbalance system were designed to 

provide excellent control and repeatability and offer progressive 

equal increments of drag and torque.

The Arrow

 fx

 fluid head also offers illuminated single control 

location for operating pan-tilt, counterbalance and viewing 

bubble level.

Introduction

Safety Instructions

 

Please use this manual to familiarise yourself with the operation 

of the Arrow

 fx

 fluid head and observe these instructions 

to prevent any damage to your equipment. Ensure that all 

equipment is operating correctly and free from defects and 

damage, also please ensure that the tripod is steady, secure and 

that the bowl is approximately horizontal when attaching the 

camera. The operator is responsible for the safe operation of this 

piece of equipment.

    Do not exceed the maximum payload capacity of the fluid 

head.

•    Do not use magnets near or around the Arrow

 fx, 

this can 

effect the magnetic rings.

    Do not leave the camera unattended on the fluid head.

•    Do not release the SLIDING PLATFORM LOCK whilst the 

camera is at an angle.

•    Do not adjust the tripod whilst the camera is attached to the 

fluid head.

•    Ensure PAN HANDLE CLAMP and CLAMP NUT is securely 

tightened.

•    Apply TILT LOCK when adding/removing equipment from 

the camera or when attaching/removing the camera from the 

fluid head.

•    Hold camera securely whilst changing counterbalance, pan 

drag or tilt drag settings.

•    Hold the camera securely whilst releasing the QUICK 

RELEASE KNOB.

•    Hold camera securely whilst adjusting the CLAMP NUT to 

level the fluid head.

Summary of Contents for 1078 Arrow fx 3

















Reviews: