Miller Electric CBI 801D, Owner'S Manual, Page: 27 / 56

OM-166 941 Page 22
Table 7-3. Approximate Air Consumption (Cubic Feet) Required To Operate Various Pneumatic
Equipment At Pressure Range 70-90 P.S.I.G.
Drill, 1/18” to 3/8” 3.75 6.25 8.75 25 Burring Tool, Large 3.6 6.0 8.4 24
Drill, 3/8” to 5/16” 5.25 8.75 12.25 35 Rammers, Small 3.9 3.25 9.1 13
Screwdriver,
#2 to #6 Screw
1.8 3.0 4.2 12 Rammers, Medium 5.1 8.5 11.9 34
Screwdriver,
#6 to 5/16” Screw
3.6 6.0 8.4 24 Rammers, Large 6.0 10.0 14.0 40
Tapper, to 3/8” 3.0 5.0 7.0 20 Backfill Tamper 3.75 6.25 8.75 25
Nutsetters, to 3/8” 3.6 6.0 8.4 24 Compression Riveter 0.2 cu. ft. per cycle
Nutsetters, to 3/4” 4.5 7.5 10.5 30 Air Motor,
1 Horsepower
3.75 6.3 8.75 25
Impact Wrench, 1/4” 2.25 3.75 5.3 15 Air Motor,
2 Horsepower
7.5 12.5 17.5 50
Impact Wrench, 3/8” 3.0 5.0 7.0 20 Air Motor,
3 Horsepower
11.25 18.75 26.3 75
Impact Wrench, 5/8” 4.5 7.5 10.5 30
Air Motor Hoist
Impact Wrench, 3/4” 5.25 8.75 12.25 35 1000# 1 cu. ft. per foot of lift
Impact Wrench, 1” 6.75 11.25 15.75 45 Air Motor Hoist,
2000#
1 cu. ft. per foot of lift
Impact Wrench, 1-1/4” 8.25 13.75 19.2 55
Paint Spray Gun
Die Grinder, Small 2.25 3.75 5.3 15 (Production) 3.0 5.00 7.00 20
Die Grinder, Medium 3.6 6.0 8.4 24 HAMMERS
Horizontal Grinder, 2” 3.0 5.0 7.0 20 Scaling Hammer 1.3 3.0 4.2 12
Horizontal Grinder, 4” 9.0 15.0 21.0 60 Chipping Hammer 4.5 7.5 10.5 30
Horizontal Grinder, 6” 9.0 15.0 21.0 60 Riveting Hammer,
Light
2.25 3.75 5.25 15
Horizontal Grinder, 8” 12.0 20.0 28.0 80 Riveting Hammer,
Heavy
4.5 7.5 10.5 30
Vertical Grinders and
Sanders, 5” Pad
5.25 8.75 12.25 35 SAWS
Vertical Grinders and Circular, 8” 6.75 11.25 15.75 45
Sanders, 7” Pad 9.0 15.0 21.0 60
Circular, 12” 9.75 16.25 23.8 65
Vertical Grinders and
Sanders, 9” Pad
10.5 17.5 24.5 70 Chain, Lightweight 4.20 7.0 9.8 28
Burring Toll, Small 2.25 3.75 5.3 15 Chain, Heavy Duty 13.1 21.8 30.5 87
MISCELLANEOUS
PORTABLE
TOOLS
Percent Use Factor And
Compressed Air Consumption (CF)
MISCELLANEOUS
PORTABLE
TOOLS
Percent Use Factor And
Compressed Air Consumption (CF)
9 sec 15 sec 21 sec 1 min 9 sec 15 sec 21 sec 1 min
Always check with tool manufacturers for actual air consumption of tools being used. The above is based on averages and should not be
considered accurate for any particular make of tool.
Above tools are rated based upon typical “on-load” performance characteristics.
For other values, adjust the C.F. air consumption on a proportional basis.
The cubic feet (C.F.) air consumption for 1 minute may also be expressed as air consumption in cubic feet per minute (C.F.M.)