background image

RouterBOARD M33G

First use

Insert the miniPCIe and M.2 cards (not included) and secure them with the included screws. [Only one
802.11 wireless card can be used at once]. It is suggested to use the other slot for LTE modems. Please
see 

MiniPCIe slot usage

 paragraph.

(Optional) Install the device in a case.

Connect cables to wireless cards and Ethernet ports.

Plug in power cable (directly or through the PoE injector) to turn on the device, please see  

powering

paragraph.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox
should be used to connect to the default IP address of 192.168.88.1 with the username admin and no
password.

We recommend clicking the “Check for updates” button and updating your RouterOS software to the latest
version to ensure the best performance and stability,

Choose your country, to apply country regulation settings (if applicable) and set up your password in the
screen that loads.

Assembly

M33G for professional use. Each of the devices comes in ESD protective packaging. When handling electrical
equipment please observe the following safety precautions:

Use a wrist grounding strap when unpacking and working with electrical components to avoid electrical
discharge (ESD) damage.

After unpacking please place the router on the anti-static mat.

When mounting unit make sure there are no objects that can damage or touch the PCB plate.

Note that ETH, USB and other ports are extending over the perimeter of PCB plate.

The device can be mounted in your desired location using the factory provided four holes in a PCB plate, located
on each side of the device.

Mounting

Mounting and configuration of this device should be performed by a qualified person.
The IP rating scale for this device is IPX0.
We recommend shielded Cat5/6 cables for our devices.
The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded.

Powering

The device accepts power with the following modes:

Passive 11-28 V DC   PoE to J1 Ethernet port. The Higher voltage needed to compensate for power loss

on long cables at least 18 V is suggested.

Direct input to the power jack DC   11-28 V.

Max total power consumption with all interfaces loaded is 24 W. Maximum power to each extension card is 3 A.
Connecting to a POE Adapter:

1. Connect the Ethernet cable from the device to the POE port of the POE adapter.
2. Connect an Ethernet cable from your LAN to the LAN port of the POE adapter, please mind arrows for data

and power flow.

3. Connect the power cord to the adapter, and then plug the power cord into a power outlet.

See mikrotik.com/products for the latest version of this document.

Document #50468 Modified on: 13.SEP.2019

Summary of Contents for RouterBOARD M33G








Reviews: