background image

Manual 

LOGO 550 

- ©Mikado Model Helicopters GmbH - Page 2

Index

OPERATING YOUR MODEL SAFELY

Operate the helicopter in spacious areas with no 
people nearby.
!Warning: Do NOT operate the helicopter in the fol-
lowing places and situations (or else you risk severe 
accidents):
• in places where children gather or people pass 

through

• in residential areas and parks
• indoors and in limited space
• in windy weather or when there is any rain, snow, 

fog or other precipitation

If you do not observe these instructions you may be 
held reliable for personal injury or property damage!
Always check the R/C system prior to operating your 
helicopter. When the R/C system batteries get weaker, 
the operational range of the R/C system decreases. 
Note that you may lose control of your model when 
operating it under such conditions.

Keep in mind that other people around you might also 
be operating a R/C model. 

Never use a frequency which someone else is using 
at the same time. Radio signals will be mixed and you 
will lose control of your model. 

If the model shows irregular behavior, bring the model 
to a halt immediately. Turn off all power switches and 
disconnect the batteries. Investigate the reason and 

fi x  the  problem.  Do  not  operate  the  model  again  as 

long as the problem is not solved, as this may lead to 

further trouble and unforeseen accidents.

! Warning: In order to prevent accidents and personal 

injury, be sure to observe the following:

Before fl ying the helicopter, ensure that all screws are 

tightened. A single loose screw may cause a major 

accident. 

Replace all broken or defective parts with new ones, 

as damaged parts lead to crashes.

Never approach a spinning rotor. Keep at least 10 me-

ters/yards away from a spinning rotor blades. 

Do not touch the motor immediately after use. It may 

be hot enough to cause burns. 

Perform all necessary maintenance.

PRIOR TO ADJUSTING AND  OPERATING YOUR  MO-

DEL, OBSERVE THE FOLLOWING

!Warning: Operate the helicopter only outdoors and 

out of people’s reach as the main rotor operates at 

high rpm!

! Warning: While adjusting, stand at least 10 meters/

yards away from the helicopter!

Novice R/C helicopter pilots should always seek advice 

from experienced pilots to obtain hints with assem-

bly and for pre-fl ight adjustments. Note that a badly 

assembled  or  insuffi ciently  adjusted  helicopter  is  a 

safety hazard!

In the beginning, novice R/C helicopter pilots should 

always be assisted by an experienced pilot and never 

fl y alone!

Tools for Assembly & R/C Equipment

Safety Instructions

Safety Instructions  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  2
Tools for Assembly & R/C Equipment  .  .  .  .  .  .  .  2
1 Mainframe .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  3
2 Tail Rotor  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4
3 Tail Boom  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5
4 Main Gear & Tail Boom Assembly  .  .  .  .  .  .  .  .  6
5 V-Bar Rotor Head .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  7
6 Servo Installation .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  8
7 Mounting the Motor .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  9
8 Canopy Mounting .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  9
9 Radio and Battery   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   10
10 Overview Chassis  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .   11
11 Overview Tail Rotor  .  .  .  .  .  .  .  .  .  .  .  .  .  .   12
12 Overview V-Bar Head  .  .  .  .  .  .  .  .  .  .  .  .  .   13

Manual Mikado LOGO 550

Note: 

There is no bag 4 and 10.  The bags are numbered 1 to 12, with the exception of 4 and 10.

Max. rotorhead rpm LOGO 550 : 2300
Max. collective range:

 +/- 12°

Max. Rotor blade size: 

 550mm

Max. LiPo Akku size: 

6S 5000mAh

LOGO 550 is not recommended for novices. This helicopter 
is a complex system. Basic knowledge of the function of 
a model helicopter is required to build and operate the 
LOGO 550.

Tools for Assembly & R/C Equipment

Radio with Heli-Software

Motor + Speed Controller (check the Mika-

do webpages for recommended motors)  

Alle shown products are examples. You may use different brands.

Scissors

Rubber Hammer

Screwdrivers 
(plus and minus)

Hex Wrenches

1.5/2.0/2.5/3.0 mm

(.055/.079/.098/.118 in)

Ball

link

pliers

Threadlock

circlips 
pliers 

Grease

Pitch Gauge

V-Bar Neo

Battery

Summary of Contents for LOGO 550














Reviews: