background image

 

Mighty Mule FM462 Installation Instructions

  

27

Gate Operator Installation Checklist

1.   The gate has been checked to make sure it is level and moves freely in both directions.

2.   Potential pinch areas have been guarded so as to be inaccessible OR have 

sensing edges and/or photo beam obstruction detection devices installed.

3.   The installer has installed one or more contact or non-contact obstruction sensing 

devices, in compliance with UL325 requirements for this installation.

4.   If pedestrian traffic is expected, a separate pedestrian gate has been installed, a minimum 

of seven feet from the gate. All pedestrian traffic must use the pedestrian gate.

5.   Warning signs have been installed on each side of the gate in highly 

visible locations. These signs must remain at all times.

6.   There are no controls installed on the gate operator, or within ten feet of the gate.

7.   The Dual Sense Technology™ feature has been properly adjusted and tested to 

make sure that the gate stops and reverses a short distance with minimal resistance 

applied (40 lbs. on a swing gate at the end of the gate, 75 lbs. on a slide gate) 

8.   Reviewed and understand all of the operational functions, 

obstruction sensing devices, warning beeper and reset, etc.

9.   Review and understand the proper use of the operator’s manual disconnect feature. The 

manual disconnect must never be used while the gate is in motion. The power switch 

must be turned off before using the manual disconnect and disengaging the operator.

10.  Reviewed all safety instructions, and keep the safety instructions 

and owner’s information sheets for reference.

11.  Review and understand the maintenance schedule for both the gate and the gate operator.

For sales call toll free:

1-800-543-GATE (4283)

The

 Sales Department

 is open Monday – Friday 8:00 

A.M.

 – 5:00 

P.M.

 (Eastern Time)

For technical service Call toll free:

1-800-543-1236 

The

 Technical Service Department

 is open Monday – Friday 8:00 

A.M.

 – 7:00 

P.M.

 (Eastern Time)

3121 Hartsfield Road • Tallahassee, Florida, USA 32303

www.mightymule.com 

Summary of Contents for MM462








































Reviews: