MM260 Installation Instructions
9
1
POWER
OFF
120
AUTO CLOSE
TIME
MIN
MAX
STALL
FORCE
ON OFF
SG1
ED1
K1
06
AVR-ISP
D1
C2
C7
C15
LED3
D15
R20
IC4
D16
D13
D14
K2
BATT- BATT+
STATUS
ANT SHLD
S9.8874
EDGE
COM
LOCK+
LOCK -
PGOK200 Rev. XC
M_BLK
M_RED
VAR2
GRN
VAR3
VAR3
VAR1
VAR4
VAR5
PF1
VAR6
WHT
GTO Inc. Tallahassee, FL
CYCLE
EXIT
SAFETY
COM
CHGR
CHGR
MIN
MAX
STALL
FORCE
POWER
OFF
120
AUTO CLOSE
TIME
MIN
MAX
STALL
FORCE
ON OFF
SG1
ED1
K1
06
AVR-ISP
D1
C2
C7
C15
LED3
D15
R20
IC4
D16
D13
D14
K2
BATT- BATT+
STATUS
ANT SHLD
S9.8874
EDGE
COM
LOCK+
LOCK -
PGOK200 Rev. XC
M_BLK
M_RED
VAR2
GRN
VAR3
VAR3
VAR1
VAR4
VAR5
PF1
VAR6
WHT
GTO Inc. Tallahassee, FL
CYCLE
EXIT
SAFETY
COM
CHGR
CHGR
MIN
MAX
AUTO CLOSE
TIME
2
3
POWER
ON OFF
SG1
ED1
K1
06
A
VR-ISP
D1
C2
C7
C15
LED3
D15
R20
IC4
D16
D13
D14
K2
BATT
- BA
TT+
STATUS
ANT SHLD
S9.8874
EDGE
COM
LOCK+
LOCK
-
PGOK200
Rev. X
C
M_BLK
M_RE
D
VAR2
GRN
VAR3
VAR3
VAR1
VAR4
VAR5
PF1
VAR6
WHT
GTO Inc.
Tall
aha
sse
e, F
L
CYCLE
EXIT
SAFETY
COM
CHGR
CHGR
OFF
120
AUTO CL
OSE
TIME
MIN
MAX
STALL
FORCE
Do not use the Dual Sense Stall Force adjustment to compensate for
a gate that is sticking or binding. Excessive Stall Force may cause
damage to the gate operator or gate system or Injury or Death.
The Stall Force adjustment controls the amount of force the opener
will apply against an obstruction before it stops and reverses
direction. The adjustment on the control board operates like a volume
control on a radio. It controls the amount of force the opener will
apply to an obstruction before it automatically reverses direction.
The Stall Force adjustment is located on the control board. Turn
the “STALL FORCE” arrow in the center of the potentiometer with
small flat head screwdriver. Adjust the sensitivity from the MINIMUM
position up to the point where the gate operates without obstructing
from its own weight or the wind conditions in your area.
You may need to increase the stall force in cold weather due to increased resistance from gate hinges. However, the adjustment must
remain as near to minimum as possible and when the weather improves decrease the setting to the appropriate position.
NOTE:
The stall force setting must at the lowest (minimum) possible position.
Close control box.
Turn the “AUTO CLOSE TIME” arrow in the center of the potenti-
ometer with small flat head screwdriver to determine how long
the gate will remain open before it automatically closes. The
limits are OFF and 3 - 120 seconds. The factory setting is OFF.
SETTING DUAL SENSE DETECTION & AUTO CLOSE TIMER
For safety reason the Dual Sense Stall Force setting on the Mighty Mule control board comes from the factory set at
MIN (minimum). This setting may need adjustment depending on the size and weight of the gate.
ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING YOUR GATE SYSTEM.
CAUTION
