Migatronic FLEX2 3000 Compact, Instruction Manual

Page: 22 / 160

22
TECHNICAL DATA
POWER SOURCE FLEX
2
3000 C
Mains voltage ±15% (50-60Hz) 3x400 V
Fuse 16 A
Mains current, effective 16.5 A
Mains current, max.. 19.0 A (380V) / 18.1 A (400V)
Power, 100% 10.9 kVA
Power, max. 12.5 kVA
No load consumption 40 VA
Efficiency 0.85
Power factor 0.90
Current range 15-300 A
Duty cycle 20°C (MIG) 300A/100%
Duty cycle 40°C (MIG) 270A/100%
Duty cycle 40°C (MIG) 300A/80%
Open circuit voltage 69-76 V
1
Sphere of application
S
2
Protection class IP 23
Standards EN/IEC60974-1
EN/IEC60974-2
EN/IEC60974-5
EN/IEC60974-10 (Class A)
Dimensions (HxWxL) air cooled/water cooled 90.6x52.4x92.5 cm/105.1x52.4x92.5 cm
Weight air cooled/water cooled 58 kg/69 kg
WIRE FEED UNIT INTERNAL COOLING UNIT
Wire feed speed 0.5-30 m/min Cooling efficiency (1.0 l. flow) 1100W (1.0 l/min)
Torch connection EURO connection Tank capacity 3.5 litres
Wire-reel diameter 300 mm Flow 1.2 bar – 60°C 1.75 l/min
Duty cycle 40°C 420A/100% Pressure max.. 3 bar
Duty cycle 40°C 500A/60% Standards EN/IEC60974-2
2
Protection class IP 23
Wire diameter 0.6-2.4 mm
Gas pressure max. 0.5 MPa (5.0 bar)
Standards EN/IEC60974-5
EN/IEC60974-10 (Class A)
FUNCTION PROCESS VALUE RANGE
Selection of trigger mode MIG/MAG 2-times/4-times
Control of current/voltage/ wire feed speed - local/torch control/remote control
Wire inching MIG/MAG Yes
Torch cooling - water cooled/gas cooled
Hot-start % MMA 0.0% – 100.0%
Hot-start-time MMA 0.0 – 20.0 s
Arc power MMA 0.0 – 150.0%
Gas pre-flow MIG/MAG 0.0 – 10.0 s
Soft-start MIG/MAG 0.5 – 24.0 m/min
Hot-start Synergic -99% – +99%
Hot-start-time Synergic 0.0 – 20.0 s
Slope down Synergic 0.0 – 10.0 s
Stop Amp Synergic 0 – 100%
Stop Amp time Synergic 0.0-10.0 s
Burn back MIG/MAG 0 – 30
Gas post-flow MIG/MAG 0.0 – 20.0 s
Sequence timer / Spot welding time MIG/MAG 0.0 – 50.0 s
DUO Plus
TM
efficiency MIG/MAG 0 – 50%
DUO Plus
TM
time MIG/MAG 0.1 – 9.9 s
Electronic choke -5.0 – +5.0
Sequence 9 sequence steps
1
S
This machine meets the demand made for machines which are to operate in areas with increased hazard of electric chocks
2 Equipment marked IP23 is designed for indoor and outdoor applications