Miele WWD 320 Operating Instructions Manual Download Page 22

Page: 22 / 84

4. Adding detergent

Detergent dispenser drawer

Any detergent suitable for automatic
front loading washing machines can be
used with this appliance. Please
observe the instructions for use and
dosage on the detergent packaging.

Filling with detergent



Pull out the detergent drawer and add
detergents to the compartments.



Detergent for the pre-wash



Detergent for the main wash




Fabric softener, liquid starch, or
capsules

Adding fabric softener



Add fabric softener or liquid starch to
the



compartment.

Do not exceed

the maximum level mark.

It will be automatically dispensed in the
final rinse. At the end of the programme
a small amount of water remains in the
fabric softener



compartment.

If starching frequently, thoroughly
clean the dispenser compartment,
especially the siphon tube, regularly.

Summary of Contents for WWD 320





















































































Search results

Summary of Contents for WWD 320

Reviews:

Related manuals for WWD 320

Brands by name

Popular brands

Miele WWD 320, Operating Instructions Manual

Search results

Summary of Contents for WWD 320

Reviews:

Related manuals for WWD 320

Brands by name

Popular brands