Miele W 502 Operating Instructions Manual Download Page 47 | Manualshive

Page: 47 / 64

background image

Levelling the machine

The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.

Failure to level the machine can result
in the machine "banging" in the spin
cycle or "walking" across the floor
during operating.

Screwing out and adjusting the feet

The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

^

Using the spanner supplied turn
counter nut

2

in a clockwise

direction. Then turn counter nut

2

together with foot

1

to unscrew.

^

Use a spirit level to check the
machine is standing level.

^

Hold foot

1

securely with a pipe

wrench. Turn counter nut

2

again

using the spanner supplied until it
sits firmly up against the housing.

,

All four counternuts must be

firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.

Installation and connection

47

«
...
45
46
47
48
49
...
»

Summary of Contents for W 502

































































Reviews:

No comments

Related manuals for W 502

Brand: GE Pages: 2

Brand: GE Pages: 2

Brand: GE Pages: 73

Brand: GE Pages: 2

Brand: GE Pages: 48

CDWT980RSS - Cafe 24" Tall Tub Dishwasher

Brand: GE Pages: 2

CDWT980RSS - Cafe 24" Tall Tub Dishwasher

Brand: GE Pages: 32

Brand: GE Pages: 64

Built-In Dishwashers

Brand: GE Pages: 48

Spacemaker WSM2480

Brand: GE Pages: 12

Spacemaker GTUP270EMWW

Brand: GE Pages: 3

Profile WPDH8800

Brand: GE Pages: 80

Appliances GFWN1100

Brand: GE Pages: 54

Brand: GE Pages: 1

Brand: Kärcher Pages: 156

Brand: Kärcher Pages: 20

Brand: Kärcher Pages: 320

Brand: Kärcher Pages: 254

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands