Miele W 2209I Operating Instructions Manual Download Page 40 | Manualshive

Page: 40 / 72

background image

The drum door does not open when you press the Door button.

Problem

Remedy

The machine is not
connected to the
electricity supply.

Put the plug in the socket and switch on.

The washing machine is
not switched on.

Switch the machine on with the

I-On/0-Off

button.

Power cut.

Open the drum door as described in the section
"Opening the door in the event of a power failure".

The door was not
correctly engaged.

Press hard against the lock side of the drum door
and then press the

Door

button.

There is still water in the
drum and the machine is
unable to drain.

Clean the drain filter and the drain pump.

For safety reasons the drum door cannot be opened if the suds temperature is
higher than 55°C.

Problem solving guide

40

«
...
38
39
40
41
42
...
»

Summary of Contents for W 2209I









































































Reviews:

No comments

Related manuals for W 2209I

Brand: Campbell Hausfeld Pages: 18

Brand: Campbell Hausfeld Pages: 13

Brand: Fagor Pages: 22

Brand: lancer Pages: 50

Brand: lancer Pages: 33

Brand: STERWINS Pages: 18

Brand: Atag Pages: 184

Brand: Waterline Pages: 31

Brand: ECG Pages: 188

Brand: SCHOLTES Pages: 52

Brand: NEFF Pages: 52

Brand: Lavorwash Pages: 80

Brand: elvita Pages: 158

Brand: UNITED Pages: 80

Brand: Hanseatic Pages: 78

Brand: Alto Pages: 35

HG4585D107636QW

Brand: Hanseatic Pages: 82

Brand: Ramteq Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands