Miele TWB 140 WP Operating Instructions Manual Download Page 58 | Manualshive

Page: 58 / 80

background image

Installation

*INSTALLATION*

58

Installation

Levelling the dryer



The appliance must not be

installed behind a lockable door, a
sliding door or a door with a hinge on
the opposite side to that of the
tumble dryer, in such a way that a full
opening of the tumble dryer door is
restricted.

Make sure the dryer door can be
opened without hindrance after
installation.

The appliance must stand perfectly
level to ensure safe and proper
operation.

The screw feet can be adjusted to
compensate for any unevenness in the
floor.



Risk of fire and explosion due to

damage to the tumble dryer.
The refrigerant is flammable and
explosive.
Do not make any alterations to the
tumble dryer. Take measures to
protect the tumble dryer against
damage.

If the tumble dryer is damaged, proceed
as follows:

– Avoid naked flames or anything

which creates a spark.

– Disconnect the dryer from the

electricity supply.

– Air the room where the tumble dryer

is located.

– Contact Miele Customer Service.

«
...
56
57
58
59
60
...
»

Summary of Contents for TWB 140 WP

















































































Reviews:

No comments

Related manuals for TWB 140 WP

Brand: VALERA Pages: 78

Brand: Chefman Pages: 16

Brand: Teka Pages: 13

Tasti-Crisp DFAF755

Brand: Dash Pages: 21

Brand: Adler Europe Pages: 60

Brand: GGMgastro Pages: 9

CLOTHES-PROCESSOR EZ 3600 CEE

Brand: Equator Pages: 16

Brand: Zephir Pages: 4

Global Design 815U

Brand: Toastmaster Pages: 16

Jet CXV TurboDryer F367

Brand: Dri-Eaz Pages: 11

Brand: Esatto Pages: 24

Brand: Venga Pages: 32

Digital Sensor 6500FRE

Brand: BaByliss Pages: 37

Brand: DAN DRYER Pages: 2

Brand: Magic Pages: 16

Brand: GE Pages: 18

Affinity FAQG7011L

Brand: Frigidaire Pages: 3

Affinity FASE7073LW

Brand: Frigidaire Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands