background image

Warning and Safety instructions

15

Using a fragrance flacon (optional accessory)

 

Only use genuine Miele original fragrance flacons.

 

The fragrance flacon must be stored in its packaging so please

make sure you retain this.

 

Caution. The fragrance can leak out of the flacon. Make sure that

you always keep the flacon, or the fluff filter with the flacon inserted

in it, in a horizontal position when carrying and do not tip or place

down on any surface.

 

Use an absorbent cloth to wipe up any fragrance which has

leaked out of the flacon onto the floor, the dryer or any dryer

components (e.g. the fluff filter) immediately.

 

If fragrance which has leaked out of a flacon: comes into contact

with the 

skin

 - wash the skin thoroughly with soap and water;

comes in contact with the 

eyes

 - rinse the eyes with clean water for

at least 15 minutes; is swallowed - rinse out the 

mouth

 thoroughly

with clean water. Seek medical advice in the case of contact with

the eyes or if fragrance has been swallowed.

 

If fragrance which has leaked out of a flacon comes in contact

with clothing, change the clothing immediately. Wash the clothing or

any cloths used for mopping up fragrance thoroughly with plenty of

water and detergent.

 

There is the risk of fire or damage to the tumble dryer if the

following instructions are not observed:

– Never refill a flacon with fragrance.
– Never use a faulty fragrance flacon.

 

Dispose of an empty fragrance flacon with the household waste

and never use it for any other purpose.

 

Please also observe the information supplied with the fragrance

flacon.

Summary of Contents for TKG 640 WP

















































































Reviews: