Miele T 9246 C Operating Instructions Manual Download Page 51

Page: 51 / 52

Buzzer

The buzzer has two volumes.

Normal (Factory default)
The buzzer sounds at the end of a
programme.

Loud
The buzzer sounds at maximum volume
at the end of a programme.

Keypad tone

An audible tone sounds each time a
button is pressed.

Factory default: Off.

Contrast

Brightness

There are ten different display
contrast and display brightness
settings.

The bar chart shows you the setting.
Factory default: a medium setting.

Standby

To save energy, the display goes out
after 10 minutes and the indicator
light for the

Start/Stop

button will start

flashing slowly.

There are two options:

Standby is activated:

– if a programme is not selected within

10 minutes of the machine being
switched on.

– 10 minutes after a programme has

started.

– 10 minutes after the end of a

programme.

not in current prog.
(Factory default)

– Standby is activated if a programme

is not selected within 10 minutes of
the machine being switched on and
after the end of a programme.
(Standby is not activated after a
programme has started).

Pressing one of the buttons switches
the display back on again.

Memory

The electronics will memorise the
drying level and any extra options
selected for the current drying
programme.

Factory default: Off.

Programmable functions

Summary of Contents for T 9246 C





















































Search results

Summary of Contents for T 9246 C

Reviews:

Related manuals for T 9246 C

Brands by name

Popular brands

Miele T 9246 C, Operating Instructions Manual

Search results

Summary of Contents for T 9246 C

Reviews:

Related manuals for T 9246 C

Brands by name

Popular brands