Miele T 8422 C Operating Instructions Manual Download Page 46

Page: 46 / 52

Altering the volume of the
buzzer

The buzzer has two volumes.

Normal
The buzzer sounds at the end of a
programme (default setting).

Loud
The buzzer sounds at maximum volume
at the end of a programme.

Follow steps

to programme

and store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button lights up

constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Low temperature

button

once.

– The

Low temperature

indicator light

will briefly flash on and off four times.

–

and

(default setting) will flash

alternately in the display.

The number which appears alternately
in the display with

means:

Normal buzzer

(Default setting)

Loud buzzer

(The

Automatic

indicator light will

also flash).

Pressing the

Start/Stop

button

switches from one to the other. You
will hear the two buzzer volumes as
you do so.

Switch the dryer off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

Summary of Contents for T 8422 C





















































Search results

Summary of Contents for T 8422 C

Reviews:

Related manuals for T 8422 C

Brands by name

Popular brands

Miele T 8422 C, Operating Instructions Manual

Search results

Summary of Contents for T 8422 C

Reviews:

Related manuals for T 8422 C

Brands by name

Popular brands