Miele T 8000 WP SUPERTRONIC Operating Instructions Manual Download Page 40 | Manualshive

Page: 40 / 72

background image

Cleaning the fine filters

The additional fine filters collect finer
fluff, hair and detergent residues which
have got through the surfaces of the
fluff filters in the door and the door
opening.

The additional fine filters

– do

not

need to be cleaned after

each drying programme. They
should only be cleaned when the
prompt* to do so appears in the
display.

* See "Make sure you clean all the
filters at the correct intervals".

– must be cleaned under running

water.

,

The fine filters must not be

replaced in the dryer dripping wet.
Squeeze them thoroughly.
If the fluff filters in the door and the
door opening have also been
cleaned under running water, they
must be dried.
Otherwise they could cause
operational faults.

,

Always replace the fine filters if

they are damaged (Miele optional
accessory, available to order).

1. Cleaning the fine filter in the door

Components of the fluff filter in the door

1 Fluff filter

2 Fine filter frame holder

3 Fine filter frame

4 Fine filter

^

Open the door and pull the fluff filter
out of the door as described
previously.

^

Remove the fine filter (4) as
described on the following pages.

Cleaning and care

40

«
...
38
39
40
41
42
...
»

Summary of Contents for T 8000 WP SUPERTRONIC









































































Reviews:

No comments

Related manuals for T 8000 WP SUPERTRONIC

Brand: XPower Pages: 6

Brand: Blaupunkt Pages: 10

Brand: Hottek Pages: 18

Brand: Haier Pages: 15

Brand: Haier Pages: 16

Brand: Haier Pages: 36

Brand: Haier Pages: 80

Brand: Haier Pages: 90

Brand: Haier Pages: 106

Brand: Haier Pages: 124

Brand: Bosch Pages: 10

Brand: Bosch Pages: 32

Brand: Bosch Pages: 10

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands