Miele T 7744 C Operating Instructions Manual Download Page 9

Page: 9 / 52

Control panel

Display

Delay start button

This button is used for:
- Selecting the duration of the

Warm air

and

Cool air

programmes

- Delaying the start of a programme

Buzzer button

An audible tone sounds at the end of
the programme.

Check lights

These indicator lights have various
functions. See "Problem solving
guide" / "After sales service" for
details.

Start/Stop button

For starting the programme selected
and cancelling a programme once it
has started.
The button flashes while a
programme is being selected and
then is on constantly when the
programme has started.

Low temperature button

Delicate fabrics are dried at a lower
temperature.

Drying level button

with indicator lights

Programme selector

with indicator lights

Door button

Pressing this button will open the
door even when the machine is
switched off at the mains.

I-On/0-Off button

For switching the dryer on and off.

Operating the tumble dryer

Summary of Contents for T 7744 C





















































Search results

Summary of Contents for T 7744 C

Reviews:

Related manuals for T 7744 C

Brands by name

Popular brands

Miele T 7744 C, Operating Instructions Manual

Search results

Summary of Contents for T 7744 C

Reviews:

Related manuals for T 7744 C

Brands by name

Popular brands