Miele T 7644 C Operating Instructions Manual Download Page 55

Page: 55 / 64

Extending the cooling down
time

The cooling down phase which takes
place before the end of a programme
can be extended by 5 or 10 minutes,
if required. This makes the garments
easier to handle.

The cooling down time can only be
extended for programmes with drying
levels.

Follow the steps (

...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Switch the dryer on.

Wait until the

Start/Stop

button lights up

constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Low temperature

button

five times.

– The

Low temperature

indicator light

will flash seven times briefly.

number

to show which option is

selected will appear in the display
alternating with the letter

Cooling down time not extended
(factory default setting)

Cooling down time extended by
five minutes

(the

Automatic

indicator light will also

flash once).

Cooling down time extended by
ten minutes

(the

Automatic

indicator light will also

flash twice).

Pressing the

Start/Stop

button

switches between the options.

Switch the dryer off.

The setting you have selected is now
stored in memory. You can change it
again at any time.

To check the setting:

Carry out steps

Switch the dryer off after step

Programmable functions

Summary of Contents for T 7644 C

































































Search results

Summary of Contents for T 7644 C

Reviews:

Related manuals for T 7644 C

Brands by name

Popular brands

Miele T 7644 C, Operating Instructions Manual

Search results

Summary of Contents for T 7644 C

Reviews:

Related manuals for T 7644 C

Brands by name

Popular brands