background image

Description of the machine

Additional display with selector button

Selector button “Residual moisture” /
“Time” / “Vented air”

“Residual moisture” (%)
With this button the programmed residual

moisture values in programmes 

1

 to 

9

 can

be altered.

“Time” (h/mins)
With this button the programme duration can

be changed in programme 

0

  (003 minutes

to 1.00 hour), and in programme 

!

  (003 min-

utes to 3.00 hours).

- These changes can only be carried out be-
fore the start of the programme.  Changes are
only valid each time for one selected pro-
gramme.  At the end of the programme the val-
ues set revert to the standard values. -

“Temperature of vented air” (

o

C)

If the button is pressed in while a programme
is running and released immediately, the cur-
rent vented air temperature will show in the ad-
ditional display for approx. 5 seconds. There
is no display for the "TR" models.

“Residual moisture” / “Time” / “Vented air”
display 

(Standard programming, see p. 19)

“Residual moisture” (%)
Display of the residual moisture set for pro-

grammes  

1

 to 

9

.

A few minutes after the programme has
started the residual moisture in the laundry is
recorded and displayed.

The current residual moisture values are
shown continuously during the programme.

“Time” (h/mins)

Display of the time set for programmes 

0

and 

!

.

The hours are shown in the left hand display
field and the minutes in the other two fields.
After the programme has started the remain-
ing time left to run is shown instead of the total
time.

“Vented air temperature” (

o

C)

Display of the current vented air temperature
while a programme is running. Display lasts
for approx 5 seconds. There is no display for
the "TR" models.

Note:

After the start button has been pressed a turn-
ing circle is shown for a short time in the dis-
play (meant to represent the turning drum of
the dryer).

Indicator lights “Residual moisture” /
“Time left”

“Residual moisture”
Lights up when the machine is switched on

and programme 

1

 or 

9

 is chosen.

It goes out at the end of the programme.

“Time left”
Lights up when the machine is switched on

and a programme between 

0

and 

!

 is chosen.

It goes out at the end of the programme.

Selector button

Display

Indicator lights

9

«M.-Nr.04989220/02 - GB - »

Summary of Contents for T 6251



























Reviews: