manualshive.com logo in svg

Miele T 4892 C, Operating Instructions Manual

Share
Download
Miele T 4892 C Operating Instructions Manual Download Page 36

Problem

Possible cause

Remedy

The following
message appears
after the
programme has
finished:

Clean the filters

The dryer is not working
efficiently or
economically.

Possible cause: The filter
is clogged with fluff or
with detergent residues.

–

Cleaning the filters is usually
all that is required.
However, if the message
does not go out after you
have cleaned the filters, then
also check all the possible
causes described under "The
drying process goes on too
long or even switches off".

To delete the fault message:

–

Switch the dryer off and then
back on again.

You can adjust the setting which
controls when or if the message

Clean the filters

appears.

See Settings menu

J

, Airways

indicator.

,

Technical fault

– the programme

is cancelled.

– the buzzer

sounds

No obvious cause.

In some circumstances,

Clean the filters

has

already been displayed.

–

Clean the filters and the
condenser unit.

To delete the fault message:

–

Switch the dryer off and then
back on again.

There is a fault if, despite
doing this, the
programme is cancelled
and the fault message
appears again.

Contact the Miele Service
Department.

i

Programme finish
time changed

This is not a fault.

Settings were changed while the
timer was counting down to the
start of a programme, or there
was a power cut.

Problem solving guide

36

Summary of Contents for T 4892 C





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands