Miele T 4888 C Operating Instructions Manual Download Page 10

Page: 10 / 60

Displays

Entry menu

COTTONS

PROGRAMME SELECTION ...

2 MINIMUM IRON

SETTINGS

...

3 WOOLLENS HANDCARE

4 SMOOTHING

10:00

When the machine is switched on, the entry menu (with
factory default settings) appears and

Programme Selection

highlighted.

Multi-function selector

Turning

the multi-function selector moves the highlighting to

the next menu option.

Pressing

the multi-function selector selects the highlighted

menu option.

Short cut buttons

Pressing a short cut button selects one of the four favourite
programmes, which appear on the left of the display. You
can customise the favourite programmes to suit your own
requirements.

The short cut buttons have different functions in the other
menus. Where this is the case, an arrow

will appear in the

display above the short cut button, together with a
description of its function .

Programme selection

There are two ways of selecting a programme:

– Option 1: Select the

Programme Selection

menu in the

display and confirm your selection by pressing the
multi-function selector.

– Option 2: Press short cut button

, or

. This will

automatically take you into the main menu of that
programme.

Operating the tumble dryer

Summary of Contents for T 4888 C





























































Search results

Summary of Contents for T 4888 C

Reviews:

Related manuals for T 4888 C

Brands by name

Popular brands

Miele T 4888 C, Operating Instructions Manual

Search results

Summary of Contents for T 4888 C

Reviews:

Related manuals for T 4888 C

Brands by name

Popular brands