manualshive.com logo in svg

Miele T 4819 Ci, Operating Instructions Manual

Share
Download
Miele T 4819 Ci Operating Instructions Manual Download Page 22

Woollens handcare

Max. load 2 kg*

Fabric

Woollen fabrics

Note

– This programme only fluffs up woollen garments. They are

not dried completely by this programme.

– Remove garments as soon as the programme has finished

and leave to finish drying at room temperature.

Low temperature

Low temperature cannot be deselected.

Proofing

Max. load 2 kg*

Normal

Fabric

For drying microfibre fabrics, skiwear, fine, closeweave cotton
garments (poplin) or tablecloths which are suitable for drying
in a tumble dryer and have been treated to provide a water
and dirt resistant finish.

Note

– This programme includes a proofing fixing phase.

–

Only use proofing agents containing fluorochemical
compounds which are stated by the manufacturer as
being "suitable for use on membrane textiles".

–

Do not dry items which have been treated with proofing
agents containing paraffin. Fire hazard!

Express

Max. load 3.5 kg*

Extra dry, Normal, Hand iron, Machine iron

Fabric

Fabrics which can tolerate high temperatures with the

q

symbol on the care label and which can be dried in the

Cottons

programme.

Note

– The programme duration is shorter.

Automatic plus

Max. load 4.5 kg*

Normal, Hand iron

Fabric

Mixed loads of garments suitable for the

Cottons

and

Minimum iron

programmes. Sort according to colour.

Denim

Max. load 3 kg*

Normal, Hand iron

Fabric

Denim garments, e.g. jeans, jackets, skirts, shirts.

Low temperature

Select the Low temperature option for delicate fabrics with the

r

symbol on the care label.

* Weight of dry laundry

Programme chart

22

Summary of Contents for T 4819 Ci





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands